Jump to content
SAU Community

Recommended Posts

On the 1RM, what is a good way to test that out? ie after you have stretched, warmed up etc how many sets, what weights should you do before you try and hit the 1RM or doesnt it matter?

I tried bench on Monday but I 'think' I did too many sets first?

60x12

80x10

100x6

110x4

120x1 - this was the 1RM effort - spoilt by a spotter who jumped in at the first sight of struggle, despite being told not to!

Cheers.

Been a while but finally managed to work out some 1RM's;

120kg bench

165kg deadlift

110kg squat (no comments lol)

Decided my starting weights on the PPP are going to be;

130kg bench

180kg deadlift

120kg squat

I figured that if I go through the program and it becomes too much on a certain week I will drop to the lower weight program for that week and do the weights stated there. I didnt want to start too low and not gain much overall improvement on the PB.

So started the deadlift PPP yesterday and was OK. Lower back feels it today. Today off and tomorrow chest.

Squat and deadlift are great. Bench is a bit low compared to them, any reason? What do you weigh again?

A competition bench is done with a pause on the chest, bum on the bench, feet cant move

Many that have lifted at my novice comps are stunned how much they lose when they have to it properly

That will be a great total Nick at sub 90kg, 565kg at your first States is great. Max did 462.5kg at his

Very different to a gym lift

Many that have lifted at my novice comps are stunned how much they lose when they have to it properly

Although it's sometimes a downer first time you try, once you learn how to do it properly it eventualy helps you lift more. Most people don't drive through their feet etc.

Edited by rev210

Oh, I agree. Max's PB is 155kg paused, he's never tried more touch and go. In fact he pauses all his reps now

Gym lifters drop over 10kg when they try to pause, some drop another 10 when they have to touch there chest

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...