Jump to content
SAU Community

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Yeah Bob & wolverine, I imagine the RB30 should provide the torque the stag needs; will post dyno sheets & all, but im yet to drive it or start it for that matter! Still got some work to do, like manual conversion & rear manual subframe from GTR, plus finish brake conversion & then tune! But, im expecting over 350awkw & a truck load of torque, so im sure that will get it off its fat arse!

My s1 has elec mirrors, I assumed they all did?! As for what to look out for, well like any car, things age & wear. If its had an easy life & kept well maintained, it should run happy for years. But things occasionally do go wrong & such is cars! If its done over 100k then check if it had its major service & timing belt done. No turbo noise. Good compression. Good cooling system. etc... Service history? Then should be ok!?

Rust under the mirrors is common. Broken or missing door weather strips (expensive & somewhat difficult to get). The mechanicals are very much the same as the R33 GTR & motor is R33 GTST (s1) or R34 GTT (s2) or R33 GTR (260RS)! Read all the threads, it will give you a pretty good idea of whats going on with Stageas & what people want or have problems with, lots of info in the stickies too!

These cars are pretty tough to a point, so if left std & driven normally, then you shouldnt have any real issues! If you chose to mod &/or drive "spirited", then you have "swallowed the red pill" (time to get your hands dirty & your wallet cleaned)!

Buy one, they're awesome!

Is the only reason not to pick an 260 due to the price what are the engines like and performance upgrades are they easy as on the other motors like say if they were they same price to buy and u put the same money or mods on which would end up a better car performance and drivability and life of the car

The Autech 260RS is the better car, though very similar to the RS4S in most areas. The 260RS is an R33 GTR mechanically! The RS4S uses the R34 GTT engine & has standard s2 Stagea brakes (smaller than the 260RS Brembos), different body kit, along with a few other minor changes! But the RS4S is roughly half the price over here! So with the money saved, you could make the RS4S better for less, if you want to mod it! But if money is no issue or you dont want to mess with it too much, then the 260RS is the best Stagea in the range (besides the elusive Nismo Stagea, which is mechanically the same as the Autech 260RS anyway)!

Performance = 260RS

Value = RS4S

If your going nuts on building a monster, then might as well use a S1!

Basically, If I won Lotto or something I would hunt down & buy the Nismo 260RS, just to have it on the compliance plate, but seeing as I have a S1 RS4V already, I would just finish building that, as it wouldnt matter which car I started with, they'd both end up the same!

They all have a very similar drivability, all offer similar performance once modified, life of the car is the same!

Just work out your budget or other confining factors, what you want/need to do with the car; then decide on which best suits your needs & wants! (There isnt a bad Stagea, they are all awesome, thats why we own them!)

Zorro has the right of it.

If you are budget conscious then it's hard to go past an S2 RS4S (or S1 for that matter). It's 85% of the 260rs for half the price. To make it 120% of the RS will still cost less than an RS. But then, at the end of the day, it's not an RS.

If you specifically want an RS because it's an RS then go for it, I doubt you'll be disappointed. Just bear in mind there is a cheaper way to get into a stag or cheaper a way to get into a faster stag by starting with an RS4S.

Auto's only

1 for snow (2 gear takeoff i think, maybe also 50/50 torque split)

power is auto too (earlier kickdown)

auto's also have the awd button (locks 50/50 up to like 40kmh or something like that)

Manuals get none of this

Are there any problems with any models as you put the kms on these cars want to what the life of them are like

The stageas are built well mate. Mines just passing 210,000kms with nothing but regular servicing. Including alot of hard driving and even a few track days. Except for a clutch which is the result of abuse with the front shaft out :D

Do they have a speed limiter at 180km is it possible to override or remove this

Do the rs4s all have the neo engine ?

I honestly believe ALL your questions and queries will be answered by inspecting a few C34's and M35's, test driving both.

Otherwise this thread will drag on forever without a final conclusion and you'll still be none the wiser.

Do they have a speed limiter at 180km is it possible to override or remove this Do the rs4s all have the neo engine ?

yes and yes

all s2 c34's have neo's

and the manuals only came out as s2's (apart from the 260rs's)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...