Jump to content
SAU Community

Recommended Posts

I have searched, perhaps my skills in doing so aren't quite up to scratch but have done so regardless.

http://www.skylinesaustralia.com/forums/topic/218752-nismo-fuel-pump-for-32-gtr/

So I plan on using a Nismo pump in a 33 gtr, to my understanding, they flow 276L/h @ 12.5V

Stock wiring to fuel pump generally does not see 12.5V does it?

Therefore I'd like to know if it is just as important to rewire for the Nismo as there was no answer to

a similar question in the above thread.

Regards

Michael

Link to comment
https://www.sau.com.au/forums/topic/408068-nismo-fuel-pump-rewire/
Share on other sites

Absolutely. Run a new wire from the battery and a relay. Make sure the wire is 6mm and just trigger the relay from the stock power feed.

Thanks for clarifying, so it can be done exactly like so on an R33 GTR right?:

http://www.skylinesaustralia.com/forums/index.php?app=core&module=attach&section=attach&attach_rel_module=post&attach_id=289665

It's a little bit confusing because the below diagram seems to teach a slightly different method (or is it the same?):

http://hosting06.imagecross.com/image-hosting-07/7591FUEL.jpg

Is there one method which betters the other?

The former (NARVA relay) seems easier.

When i rewired the fuel pump in my 33 GTR (nismo unit) i rewired the WHOLE thing. I got rid of the fuel pump speed controller, ran new earth and new feed and relay with a fuse in line, cost me about 50 bux in parts(heatshrink, solder, relay, inline fuse holder, some QUALITY terminals)

No I mean the diagram just looks like a standard 5 pin relay setup. Nothing special.

Or was the purpose of the diagram to explain how a relay is wired?

Oh yeah just to put it in a drawing. I found the DIY a biit confusing (where its just written) so thought I'd do a diagram that shows how to do it with the R33 wiring. Its a basic circuit but might help the OP. Only problem I had figuring it out was working out the positive feed because I didnt have anything to test it so just made up a test light. And yes forgot to add the fuse in. I have a 20amp fuse between battery and relay Edited by 89CAL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...