Jump to content
SAU Community

Recommended Posts

Hey, you know how Turbo is illegal for P Platers in NSW. Is there a way to get the engine modified to have the turbo's underneath or in the middle of the engine, or some place where they are hidden and if a copper looks inside the engine they can't see them?

Link to comment
https://www.sau.com.au/forums/topic/408513-turbo/
Share on other sites

Yeah, remove the sump, fit the turbo in there and re-fit the sump and no-one but you will ever know its there

Remember to re wire the turbo to the air control unit otherwise it will leak fluid and the cop might see that.

But yeah do this!

Cheap as well it's about $250 from what I remember when I did it on my P's

Link to comment
https://www.sau.com.au/forums/topic/408513-turbo/#findComment-6517713
Share on other sites

Hmmmmm... I remember this guy

But for serial, mount turbo in wheel arch.

They never look there.

Oi zeb, Ill be around to help with the turbo install, did you get your relocation kit?

Just unloading the container now, should be in here

Link to comment
https://www.sau.com.au/forums/topic/408513-turbo/#findComment-6517778
Share on other sites

You ask a question, people answer, then you get upset at them. They even gave you the answer you wanted, yes it's possible, via any number of ways. your only other option is to remove the turbos all together and run an NA ecu until you are on your open licence, but you will lose performance.

Link to comment
https://www.sau.com.au/forums/topic/408513-turbo/#findComment-6517843
Share on other sites

You ask a question, people answer, then you get upset at them. They even gave you the answer you wanted, yes it's possible, via any number of ways. your only other option is to remove the turbos all together and run an NA ecu until you are on your open licence, but you will lose performance.

I would do this, much less effort. Ask Benji "Bakemonoricer". He's also good with rotary head gaskets if you ever go down that road.

Link to comment
https://www.sau.com.au/forums/topic/408513-turbo/#findComment-6517858
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...