Jump to content
SAU Community

Rb20Det And R32 Parts

SIFTY32

By SIFTY32,
in Classifieds

 Share

Recommended Posts

SIFTY32 Proficient

SIFTY32

Posted
Posted

hey guys ive got a heap of spares that im selling to make more room in the garage

Rb25det s2 turbo off a low kms r33 - $300

rb20det engine loom - $140

rb20det flywheel - $60

r32 LCA's - $70

various autometer gauges - $60 each

apexi turbo timer - $50

pod filters - $20 each

r32 5 stud front hubs - $70

r32 centre A/c vent (average) - $50

RB20DET intake manifold with throttle body, tps and fuel rail - $100

RB20DET exhaust manifold - $60

rb20 manifold heat sheild - $30

rb20 turbo oil and water lines set - $40

rb20 turbo heat sheild - $30

r32 gtr fuel pump - $80

RB20DET - harmonic balancer - $60

RB25DET starter motor - $65

RB20DET starter motor - $65

RB25DET cas - $100

RB20DET cas - $100

RB25DET crossover pipe no bov - $40

RB20DET engine mount brackets - $60

RB25DET engine mount brackets - $60

rb20 p/s pump bracket - $20

RB20DET hicas p/s pump - $80

rb20 a/c pump bracket - $20

RB20DET afm - $60

R32 GTST dash cluster blue type - $90

R32 GTST dash cluster grey type - $90

RB20/25 dump pipe - $30

RB20/25 turbo intake pipe - $30

RB20 crossover pipe with stock bov - $60

RB25 crossover pipe with stock bov - $60

R32 sedan power window switch - $100

R32 coupe power window switch - $60

R32 boot lid needs some holes fixed and a paint - $50

RB20 aac valve - $50

RB20 coilpack loom - $80

RB20DET coilpacks all working perfect - $130

RB20DET ingiter - $90

R32 cusco strut brace - $100

R32 stereo/shifter surround $120

R32 window wipers - $20

R32 manual crossmember - $50

R32 clutch fork with throw out bearing carrier - $70

R32 manual sandwich plate - $40

RB20 fuel rail with stock fpr -$20

RB20 a/c compressor - $90

RB20 injectors - $60

RB20 exhaust manifold - $60

RB20det ecu (mines tuned)- $150

RB20 timing belt covers (both covers) - $60

R32 headlights projector type - $240

R32 indicators orange type - $140

R32 indicators clear type - $140

R32 coupe rear bar - $70

R32 rear calipers with new pads - $80

rb20 cas mounting bracket - $30

r32 sedan tail lights - $40 each

r32 sedan rear bumper poor cond $30

r32 rb26 cas - $100

r32 rb26 ignitor - $100

r32 rb26 coilpacks - $130

I have more stuff lying around heaps of interior bits and random stuff so if you need something just ask

pickup from springwood

Link to comment
https://www.sau.com.au/forums/topic/408700-rb20det-and-r32-parts/
Share on other sites
GH05T Grand Master

GH05T

Posted
Posted (edited)

ignitor in total working order? Post to Adel 5114?

are the clear indicators totally clear or with the orange part?

if their totally clear ill have them toorb20 ignitor

Edited by GH05T
  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...