Jump to content
SAU Community

Recommended Posts

Can someone tell me what size the heater core hoses on the firewall are and what fittings i need. when I do take them off to bypass the core should I bleed the system after to get any air out. Where are the coolant bleeder valves on the engine?

Check where the loom comes through the firewall

If the bung hasn't been seated properly it can leak through that

id say its this if its been raining

have u had a stereo installed? if they made the hole too big, itll leak water back in. Thats what happened to me

jnr

Im pretty sure it's the heater core and it's leaking into the foot well through the air con duct

I have had that problem before but I don't think I have it now. When your heater core is leaking your windscreen steams up all the time and you should (I can't remember though it was 4 -5 years ago) notice that the coolant level is going down.

My coolant level stays the same and I think water only comes in when it rains hard or I wash the car so I think my current problem is elsewhere.

  • 2 months later...

ive had the same issue on 2 c34's. one was a 97 rs4 and the other a 98 autech. only happens when it rains and only affects drivers footwell. its not soacking wet just mildly damp and smells like wet dog if ya leave it locked up for the day. doesnt rain much here so i just crank the fan in the footwell to dry it up. be nice to know where to look as it seems a common fault or design flaw.

I assumed the rain was getting in somewhere and was looking for the drains from the sunroof(s) but the recent spell of hot weather alerted me to another cause - there was no water under the car from the aircond so I assume that the drain is blocked or mis-aligned and that is what is causing it. Will check it out on the weekend.

(A leaking heater radiator normally results in not just water in the foot wells but also steamed up front screen)

  • 1 month later...

Well I finally have the leak only when it rains. Funny it did not leak when Oswald dumped his load, it started after. Looking under the dash, there is some rust on the steering column cover near where it goes thru the firewall. May be a leaky windscreen. Hope not.

I've pulled the 'beaver panel' plastic panel under the windscreen out twice and i have siliconed and re seated/joined the rubbers around the affected area.

i've taken pictures of where it is possible for water to get in, and what i have done to fix it... Fingers crossed it's fixed it.

I've pulled the 'beaver panel' plastic panel under the windscreen out twice and i have siliconed and re seated/joined the rubbers around the affected area.

i've taken pictures of where it is possible for water to get in, and what i have done to fix it... Fingers crossed it's fixed it.

Can you post up the pics please?

It looks messy, but it 'should' do the job, and last for years.

I read the green window holder was a culprit and you could push it with your fingers via the fan blower. (Having already taken it out twice, i could not be bothered to see for myself)

The beaver panel rubber is another factor, if it's broken it will let too much water in causing it to pool and run back in under the window.

If the drain gap is blocked, the same thing will happen.

The window surround also needs to be firm and flat against the body and the window.

Use screws instead of the clips, screws wont move and it sits firmer eliminating most of the water run off from entering under the beaver panel.

I'm not 100% sure this will fix the problem, but from what I've seen and read this is the major cause of water leaking into the cabin. also use a silicone/glue that isn't harmful to rubber.

post-108100-0-23921900-1362360489_thumb.jpg

post-108100-0-77266100-1362360502_thumb.jpg

post-108100-0-70361000-1362360510_thumb.jpg

post-108100-0-82416300-1362360520_thumb.jpg

post-108100-0-97002800-1362360527_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...