Jump to content
SAU Community

Recommended Posts

Hey guys,

I recently did a turbo upgrade and everything was fine for a couple of weeks (just a bit rich). Driving home from spectating Powercruise i was getting on the highway and when i pushed the throttle in, it gave a small pop and then started to miss under full throttle.

The car has a Stinger EMS ecu, GTR injectors, GTR fuel pump, Yellow Jacket Coil packs.

So far i have checked/cleaned the plugs (covered in carbon), Taped the coil packs, checked for vaccuum leaks, checked the fuel maps, used a multimeter on the ignitor (wouldnt read anything on ohms)

I have searched this forum and many others for possible causes and solutions and so far have come up with nothing.

Any help would be appreciated, even if you have a spare ignitor/AFM around Brisbane that i can test to rule some things out would be awesome.

Edited by bunnyfart

Massive thanks to SIFTY32 for letting me test his ignitor and coil packs. Nothing changed when i put his on so that rules them out. I ran a data log on my ECU and when i had my foot to the floor with no load the TPS was jumping from 100 (full open) to around 70 - 80 (not full open). My thought process is that the TPS is telling the ECU that my foot isnt to the floor when it actually is.

Is there a decent way to test the TPS with a multimeter?

Do u have an aftermarket throttle body?

I have had 2 cars lately that have had freeplay between the tps and throttle shaft.

Use a multimeter between the Signal wire and the earth wire.

Should read around .5v closed and 4.5v open completely

standard throttle body. Used the multimeter on the 2 wire and got 1.9 ohms but when i started to move the throttle butterfly it made the multimeter turn off until it was returned to closed.

I changed it to V and got 1.0 on closed and again it turned off when it was opened

Edited by bunnyfart

Ok, it seems my missfire has been solved by disconnecting my aftermarket water temp gauge from the 2 wire sensor.

Its running really well now with better fuel consumption and able to rev really easily.

Can anyone explain to me why the water temp sensor would cause such a massive issue with my car?

I never understand people that wire things in without researching.

Yes thet makes perfect sense as the coolant temp sensor is very sensitive to voltage. It even runs its own seperate sensor ground with only a few sensors like TPS and CAS.

Glad u found the issue

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...