Jump to content
SAU Community

Recommended Posts

I've been reading through a bunch of threads with similar issues yet nothing that directly relates so far.

If have a BNR32 GT-R and it's been a long cold winter here in Melbourne and the car felt like it was running fine and smooth the whole time. As there's been few warm days recently its been causing the car the run with rough idles and almost stalling at times. It will only happen if its on a warm day of more than 20 degrees.

I've also noticed that the engine check light will flash at times and then be ok again but other than that car will boost ok and give off consistent power.

So far I've read that it could be one of the vacuum lines in the plenum or the timing itself. My guess is that it could be the AFM's or sparkplugs. I am running stock AFM's with an ARC Airbox.

I also took it to be Dyno tested to see if the issue could be replicated but they found nothing aside from it running slightly hotter than usual after load. I am running an aftermarket radiator as well. However it was fairly cold day so it may have been easily spotted.

Was wondering if anyone else has had experiences with this and any suggestions would be appreciated!

Anytime the engine light flashes, the ECU will store that error code until you either clear it via CONSULT or disconnect the battery. Either read the error flashes from the ECU, or get yourself a CONSULT cable or one of these: http://ecutalk.com/consultlcd.aspx and grab that error code.

When were the spark plugs last changed, and what type are they (copper, platinum, iridium etc).

Can you hear any hissing (vacuum) in the enginebay while idling?

If you spray something with alcohol (wd40, brake cleaner, aerostart etc) around the intake manifold, ITB's, vacuum hoses does the RPM (engine changing note) temporarily rise?

Things that go wrong when hot but work fine cold, generally don't rule out the coilpack ignitor or the crank angle sensor. Until you get that error code, it's all guesswork and you might even be on the wrong track.

Thanks for the suggestions there. I'll go down the CONSULT route for now and see what its telling me first.

Sparkplugs I'm running are just NGK Platinums but I don't remember the gapping of it. But they are almost 2 years old now so may need to pull them and check. I changed the coilpacks a few years ago to Splitfires so I somehow doubt that would be it. :-/

Can't hear any hissing or vacuum leaks so far but will check further there but I haven't tried the WD40 with the intake manifold yet but if RPM rises for a bit is that a good sign?

thats the sort of thing that was happening when i had a intake manifold leak, was fine til it was at operating temp, got worse every day

the leak makes it run lean and thats what makes it rough and stall, but the opposite happened on full throttle, id get some big black clouds out the back, fill up half the street ..also seeing boost but not feeling the power for a few seconds cause it was blowing out the manifold... any of that happening?

Edited by SliverS2
  • 3 weeks later...

Manifold leak I'm still investigating as it seems to run ok 90% of the time.

Since its been getting warmer recently I've noticed it happening more often and I can sort of replicate it if I deliberately try to stall it where it will take over and try to keep the revs up. It will then start 'hunting' for up to 10-15 minutes afterwards.

Cruising along at constant speed it will feel erratic during that time.

I'm starting to count on the AFM's needing replacement in this case.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...