Jump to content
SAU Community

Recommended Posts

Interest so far

Once we have numbers i'll sort out payments etc

1. 4bidn1 X2

2. stag love

3. infiltrator

4. xntrq

5. waino

6. 3Katz

7. shotpointblank

8. rayisboostin ?

Ray postage should only be approx $10 as the packaging is quite small, Count you in ye or ne?

i'll leave this open for a few more days and then i'll send out deposit details, Turnaround from deposits received should be approx 7 days

Cheers guys

Interest so far

Once we have numbers i'll sort out payments etc

1. 4bidn1 X2

2. stag love

3. infiltrator

4. xntrq

5. waino

6. 3Katz

7. shotpointblank

8. rayisboostin ?

Ray postage should only be approx $10 as the packaging is quite small, Count you in ye or ne?

i'll leave this open for a few more days and then i'll send out deposit details, Turnaround from deposits received should be approx 7 days

Cheers guys

sorry guys im out. because i wanted so many i got the good price over the counter. thanks though :)

I'm in SA

Postage should be around $8 aus wide.

Price may come down a bit but not by much, 8 is what's needed to get this going but i would like to have a few extra to account for last minute backouts

Ok i'll be sending payment info to interested parties

Payment will need to be made within 3 days

once monies have been received it will take roughly 3-5 days for stock to arrive

and i'll have these posted ASAP

Cheers Guys,

Pete

Payments received so far

1. 3katz

2. juzzy.melb

Still only 2 payments so far if you have shown interest please check your PM's for payment details

This has taken a bit of effort to sort out so please give me an indication if your still interested in the GB

Cheers,

Pete

Edited by Fgjoh

1. 4bidn1 X2

2. stag love

3.

4.

5.

6. 3Katz

7. shotpointblank

8. juzzy.melb

9. 533ryc

Payments received so far

1. 3katz

2. juzzy.melb

3. 533ryc

waiting for payment to clear

4. 4bidn1 X2

5. Shotpointblank

6. stag love

Still only a few payments so far if you have shown interest please check your PM's for payment details

I'll be refunding monies received if minimum numbers can't be met I'll re check payments tomorrow guys

If this doesnt go ahead i'll be requesting refund details within the next day or so

Cheers,

Pete

Edited by Fgjoh

Sorry guys but 2 more just backed out so this is now no longer going ahead. Anyone who has made payment please PM me with your bank details

Thanks to those who actually followed through but without at least 7 i can't get the discounted price

cheers,

Pete

Welcome to the world of Group Buys. :/

It's a shame when people get super excited about a great idea, but then don't have the stones to admit that they can't really afford it.

Would it be worth posting in the GB section, as you might still be able to get the numbers; just not all Stagea owners.

Good on you for having a go. :thumbsup:

Good idea Dale. Unfortunately I see another yet another SAU members car has been stolen recently, I'll certainly be getting one myself. I like the idea of potentially being able to find my car and perhaps the person/s responsible - to report to police of course. I'll hold off for a while incase Pete decides to have another shot in the GB section although one could hardly blame him if it were too much trouble.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...