Jump to content
SAU Community

Recommended Posts

Hi Guys,

I got a Cobb and have been using Stage 2 & LC5 for my ADM2009 on the road since. Great burst of power and improved drivability.

(I'm on 98RON Shell vPower, HKS res midpipe, K&N air filter element)

I took it to Phillip Is (18 deg C) and Sandown yesterday (23 deg C).

I noticed flashing of the boost gauge - which I think means that there is "knocking". This usually happens after the 3rd or 4th lap, especially if I hit the rev limiter. Sometimes it occurs even at 5000rpm in 2nd gear and tends to linger for about 5 to 10 seconds. I feel the car is not as fast as it normally is.

How do I fix this?

Is this BAD for the engine?

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/411598-knocking-with-stage-2-cobb/
Share on other sites

Thing is, it doesn't do it when I drive on the road.

The Stage 2 is the Off-the-shelf map that came with the Cobb, which I thought was conservative.

What parameters should I log?

Thanks for the reply, Martin. I received your Trans Fluid 35TML last week and filled it up before Sandown. Goes nicely.

Sounds just like the tune is street conservative, but not track conservative (3-4 laps heat++ etc) - they are two totally different scenarios really.

Good news is it's not a major fix required, but certainly shouldn't keep trying to replicate it! Knock = bad.

So maybe after 2 laps have an easy 1 rather than going for 3-4 (until its fixed) :)

Does that meant if I get a track-oriented tune, it would generate less power? Because it would have to dial down the timing or boost to cope with heat.

Would larger injectors to fix this?

No point in speculating about it, you need to generate a log of some third and fourth gear pulls and then let me have a look through it. Either that or get the right map for your car running Aussie 98 fuel - such as the tune we supplied for Duncan Forrests GTR that won the NSW Supersprint championship two years in a row. No knocking, plenty of power.

OTS Cobb maps are ok, but they tend to not be a bit sketchy when pushing the limits of our 98 fuel - as they simply dont calibrate on it in the US. Regardless of what you do, that flashing engine ligh it something to take note of, and try to avoid if the idea of rebuilding an engine scares you even just a little bit :)

If you want someone local (Bayswater-Vic) the guys at Racepace can put it on the dyno for you and they have the Cobb tuning software.

9762 9421

But I've seen a few R35's knock at Sandown and PI as they have a lot of engine load at those tracks.

Ok maxzugkraft I have had a chance to have a look at a few of your looks. Looks like the tune is working really really nicely, the only time there was any indicated knock (false knock) was when you shifted on the rev limiter. The yellow line in the picture below is 'knock' and as you can see it stays on zero the whole length of the run...which is very nice :)

486666_10151212210434571_56066567_n.jpg

Thanks Martin.

I can't see your picture. There is a question mark instead.

Will this tune work for warmer weather? 25-28deg C?

Bear in mind the log was done at 15 deg C ambient temp.

Is it running too rich, as I'm getting a lot more black soot on back now.

Thanks Martin.

I can see your screenshot now.

Now I can use full power without holding back!

Can't wait to get back on the track!

Hope to see lap times plummet.

Good job. Cheers!

If you want someone local (Bayswater-Vic) the guys at Racepace can put it on the dyno for you and they have the Cobb tuning software.

9762 9421

But I've seen a few R35's knock at Sandown and PI as they have a lot of engine load at those tracks.

Would you recommend some further intercooler upgrades on top of the custom dyno tune?

Pinging at 18degC or 23degC ambient temp is pretty bad.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • New or used transmission? Alignment will be the same with engine running or not. If new, i'm presuming it's a clutch release bearing size issue. If used, are you certain it's a CD009/A and not an older CD008 or less? They had known synchro issues. In my opinion, these transmissions should always be purchased new, they're dirt cheap and you avoid dealing with old revisions. 
    • I like your thinking! Looking forward to see how it turns out.
    • You've got yourself a good old game of have fun. That shit is annoying as hell to remove. Thankfully for you, yours is on metal, most of the stuff I take it off is plastic, so typically hear guns are out. I normally end up continually dragging my thumb with pressure over it to get it to peel up. Eucalyptus oil then works well for getting residue and last remnants off.   Edit: plastic scraper might be worth while too. One that'll dig into the foam tape, but not scratch the paint.
    • So I ride and race motorcycles for fun and have always used a van to transport my track weapons. Figured towing a racebike with a skyline would be different and if done right could - "look fully sik" or quite cool for us grown ups lol. Pic of yours truly on two wheels I also have a trailer already kitted out to transport my bikes ...and I have a spare set of rims that match the car that I was going to rebarrel to get deeper dish at some stage but they have just been gathering dust. Sooooooo it is only logical.... Stay tuned !!    
    • If by "flap disc" you meant "chocolate wheel".... then they are OK for getting off stubborn remnants. But not for stuff with bulk depth. If by "flap disc" you meant "abrasive paint f**ker"....
×
×
  • Create New...