Jump to content
SAU Community

Recommended Posts

Hi Guys,

I got a Cobb and have been using Stage 2 & LC5 for my ADM2009 on the road since. Great burst of power and improved drivability.

(I'm on 98RON Shell vPower, HKS res midpipe, K&N air filter element)

I took it to Phillip Is (18 deg C) and Sandown yesterday (23 deg C).

I noticed flashing of the boost gauge - which I think means that there is "knocking". This usually happens after the 3rd or 4th lap, especially if I hit the rev limiter. Sometimes it occurs even at 5000rpm in 2nd gear and tends to linger for about 5 to 10 seconds. I feel the car is not as fast as it normally is.

How do I fix this?

Is this BAD for the engine?

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/411598-knocking-with-stage-2-cobb/
Share on other sites

Thing is, it doesn't do it when I drive on the road.

The Stage 2 is the Off-the-shelf map that came with the Cobb, which I thought was conservative.

What parameters should I log?

Thanks for the reply, Martin. I received your Trans Fluid 35TML last week and filled it up before Sandown. Goes nicely.

Sounds just like the tune is street conservative, but not track conservative (3-4 laps heat++ etc) - they are two totally different scenarios really.

Good news is it's not a major fix required, but certainly shouldn't keep trying to replicate it! Knock = bad.

So maybe after 2 laps have an easy 1 rather than going for 3-4 (until its fixed) :)

Does that meant if I get a track-oriented tune, it would generate less power? Because it would have to dial down the timing or boost to cope with heat.

Would larger injectors to fix this?

No point in speculating about it, you need to generate a log of some third and fourth gear pulls and then let me have a look through it. Either that or get the right map for your car running Aussie 98 fuel - such as the tune we supplied for Duncan Forrests GTR that won the NSW Supersprint championship two years in a row. No knocking, plenty of power.

OTS Cobb maps are ok, but they tend to not be a bit sketchy when pushing the limits of our 98 fuel - as they simply dont calibrate on it in the US. Regardless of what you do, that flashing engine ligh it something to take note of, and try to avoid if the idea of rebuilding an engine scares you even just a little bit :)

If you want someone local (Bayswater-Vic) the guys at Racepace can put it on the dyno for you and they have the Cobb tuning software.

9762 9421

But I've seen a few R35's knock at Sandown and PI as they have a lot of engine load at those tracks.

Ok maxzugkraft I have had a chance to have a look at a few of your looks. Looks like the tune is working really really nicely, the only time there was any indicated knock (false knock) was when you shifted on the rev limiter. The yellow line in the picture below is 'knock' and as you can see it stays on zero the whole length of the run...which is very nice :)

486666_10151212210434571_56066567_n.jpg

Thanks Martin.

I can't see your picture. There is a question mark instead.

Will this tune work for warmer weather? 25-28deg C?

Bear in mind the log was done at 15 deg C ambient temp.

Is it running too rich, as I'm getting a lot more black soot on back now.

Thanks Martin.

I can see your screenshot now.

Now I can use full power without holding back!

Can't wait to get back on the track!

Hope to see lap times plummet.

Good job. Cheers!

If you want someone local (Bayswater-Vic) the guys at Racepace can put it on the dyno for you and they have the Cobb tuning software.

9762 9421

But I've seen a few R35's knock at Sandown and PI as they have a lot of engine load at those tracks.

Would you recommend some further intercooler upgrades on top of the custom dyno tune?

Pinging at 18degC or 23degC ambient temp is pretty bad.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...