Jump to content
SAU Community

R33 Gtst - Noisy Power Steering On Startup

chilzzi

By chilzzi,
in General Maintenance

 Share

Recommended Posts

chilzzi Proficient

chilzzi

Posted
Posted

Hi all,

wondering if anyone has anything similar occur....

Basically on startup, the power steering is very noisy but then goes away once the car has warmed up.

The power steering pump has had a full reco around 18 months ago. Before then, the noise was constant.

Any help would be greatly appreciated.

cheers

t_revz Grand Master

t_revz

Posted
Posted

Is the fluid aerated/bubbly in the reservoir?

100% its p/s? Dropped the belt and rechecked ?

Would suck if say it was an idler or tensioner pulley and just sounded like it was coming from p/s pump area then let go

chilzzi Proficient

chilzzi

Posted
  • Author
Posted

Not sure, it's just really strange that on a cold morning startup the car is fine, no noises. If right then I do a dry steer, the loud noise starts. Once the car has warmed up a bit, it's all perfect and quiet!!! What the!!

  • 10 months later...
jez NF Proficient

jez NF

Posted
Posted

Not sure, it's just really strange that on a cold morning startup the car is fine, no noises. If right then I do a dry steer, the loud noise starts. Once the car has warmed up a bit, it's all perfect and quiet!!! What the!!

Pulling this up from a year ago but did you ever fix this problem....mine started doing this exact same thing this morning :(

jjman Mentor

jjman

Posted
Posted

this was the symptom of mine as the power steering pump was getting on - noisy when cold and dry steering, then would go away.

it will gradually get worse if it is indeed the PS pump.

bottom line is you can leave them for a while without any trouble.

Mine started having a noticeable effect on the slow speed steering when the car was still warming up until I did anything (replaced the PS pump).

good luck!

mad082 Grand Master

mad082

Posted
Posted

You can try replacing the fluid to help with cold temp steering. As fluid gets old and sludgey and is thicker than normal when cold. This means it isn't lubing the system as well. Draining the fluid and replacing it with fresh fluid can help.

mad082 Grand Master

mad082

Posted
Posted

I have to get around to doing it to my Commodore at some point (when I could be bothered, along with finding the cause of the slight misfire it has). had a leaky pump for ages and had put some stuff in it that was supposed to slow/stop leaks. Basically it was a thick fluid. I finally got a new pump but didn't completely flush the system (just topped it up really), so on cold mornings the steering has a bit of a notch just off straight. Once it warms up it's fine. I did some googling and that's when I found out about flushing the system (which made sense, since the fluid is thinner when warm, and on really cold mornings it was much worse, to a point where on a sub zero morning I had no power steering the first time I tried to turn the wheel).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...