Jump to content
SAU Community

Recommended Posts

Easy to source, nice and cheap: what's not to like?

I have also been in regular contact with another Y34 owner who has successfully sourced (Maxima?) brake pads, and shimmed them to fit our cars: will post part numbers when I get them...

Also, just FYI: not sure if it's a common issue (I haven't experienced it), but he had ongoing, intermittent rough-running issues, which after much diagnosis turned out to be failing ignition coils.

Just a couple of things to bear in mind: once we get enough info, it may be a good idea to create a Y34 parts/service sticky thread, as there's precious little information available on the interwebs...

Yeah i agree - i've found there's really not much info available on there however Aus-Vip.com i have found has a little.. not much.. but a little haha. I have the same intermittent rough-running issues but i had put it down to coilpacks as it seems to be the same sort of issue as what I had years ago in an S13 then replaced the coilpacks and all fixed.

I havn't bothered to buy new coilpacks yet for my Y34 but was planning on getting a set of Yellow Jackets from performance-wise.

Also I had my radiator end tanks replaced which turned out to be the same/very similar to Navara radiator end tanks so they were used :)

And when i needed new brake pads I took the worn out pads to SA Brake & Clutch and they matched them up with some replacements - no modification was needed either.

yeah: the brake pad thing seemed a little odd to me: I figure I'll be able to source a set of Endless or similar quite easily. Will do some research to ascertain whether ours are the same as the USDM M45- I'd say it's a pretty safe bet. Also, have seen a number of Y34s going at auction with what I believe to be CPV35 Brembos fitted, so it may be that we run the same brakes as a non-brembo V35, given Mr. Nissan's tendency to use interchangeable parts.... Once again: more research required.

For anyone looking for more info on part compatibility for Y34's (servicing, etc) see this thread: http://aus-vip.com/topic/2778-y34-gloriacedric-maintenance-info-part-number-listing/

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...