Jump to content
SAU Community

Recommended Posts

ok so the car in subject is a 1989 32 gtst

aircon dosnt work, need a bit of guidance from someone who knows more about electrics than me so i dont have to tip too much money into it

but must fix before summer hits!

ok so i have had the system re gassed with dye to find the leak, no leaks yet but the system is not yet operational. i assume i will have to replace something but thats the easy part.

the problem is my compressor and thermos are not switching on. i can hotwire it from the battery and switch the compressor on though so it does work.

i have had the pressure switch checked and their was another switch checked i think and that side of things work. i assume now that my aircon headunit itself has something broken in it, i was thinking next to just replace it and hope for the best.

is their something else electrical in the system though that i need to look at, or have looked at?

also does anyone have a wiring diagram for it?

Link to comment
https://www.sau.com.au/forums/topic/413008-aircon-and-how-to-fix/
Share on other sites

Hey Glyn, do you have an aftermarket ECU ?

Quality units like Haltech or Vipec, there is a setting in these that can prohibit AC.

Likely not your problem but worthwhile being aware.

Also i seem to remember you can get a daig code out of the AC headunit.

Worth searching the forums for.

Obviously checked fuses ?

Just found many threads but this was in one of them.

Climate Control Diagnostics R32

The climate control has a diagnostic mode.

Enter the diagnostic mode by pressing the OFF button for five seconds within ten seconds of turning the ignition on.

Sensor check

Sensor check is selected by pressing HOT switch (the red triangle) while in diagnostic mode. The microcomputer detects whether each sensor input signal is within correct parameters. The results are displayed on the screen.

If normal, a "20" is displayed.

If abnormal the failed sensor number is displayed. The sensor numbers are as follows:

20 - all is normal

21 - outside air sensor

22 - Inside air sensor

23 - Water temperature sensor

24 - Intake temperature sensor

25 - Sunload sensor (small sensor on the left hand side of the dashboard near the windscreen)

26 - PBR

27 - Refrigerant temperature sensor

This should tell you if any of your sensors are faulty

Link:

http://skylineowners...thread.php?t=47

hope this helps.

yeah i came across that a while ago, all was normal so the sensors seem to be working,

also side not i was wandering what 25 was... saw it the other day and i saw the electronics when the sun hit it and was thinking some model had auto headlights :P

all fuses are fine yup, and i have a nistune board, doubt that would do anything?

my sparky at work said he wanted to test all connections on the back of the unit and work backwards from their but thats allot of time and money, would be faster with a wiring diagram.

Fixed mine, turned out that the ecu was holding it back.

The ecu has a few states which it wil turn the ac off, most are safety related, but one of them is when you want full power out of your engine it will quickly switch the compressor off to minimise the draw.

I suspect when the nistune went in this was altered or something, mine was keeping that switch off. We rewired this so it listenes to the ac head unit not the ecu on that one. And bam Crispy cold air ready for summer

  • 2 weeks later...

Hmmm does a Power FC do the same and prohibit the air con?

I haven't had air con for about 2 years now :(

When I first tried to fix it, I believed that it was a faulty compressor, which I had that replaced for a 2nd hand unit. Got the gas refilled, and thought I got the air con to work again as it was icy cold on the way back from the air con workshop, but after 15 odd so minutes of driving it never stayed cold and the air was like the temp of a normal fan.

I've been thinking that it's been the 2nd hand compressor all along, like maybe because it was 2nd hand the seals were brittle and cracked, so it leaked again. Never thought to take it back as I didn't want to spend more money recon'ing the thing.

But with this thread coming to my attention, could I be off the right track, and in fact it could be linked to my Power FC?

Sorry to hijack lol, but it's all relevant!

Cheers,

Andy

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity.
    • 100% the factory sender is tapered, that is how it seals (well, that and teflon paste or tape)
    • Thanks folks - I've saved a few links and I'll have to think of potential cable/adapters/buying fittings. First step will be seeing if I can turn the curren abortion of a port into something usable, then get all BSPT'y on it. I did attempt to look at the OEM sender male end to see if it IS tapered because as mentioned you should be able to tell by looking at it... well, I don't know if I can. If I had to guess it looks like *maybe* 0.25 of a mm skinnier at the bottom of the thread compared to where the thread starts. So if it is tapered it's pretty slight - Or all the examples of BSPT vs BSPP are exaggerated for effect in their taper size.
    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
×
×
  • Create New...