Jump to content
SAU Community

Import Monster Sauvic Deca Motorkhana - 8Th December 2012 - Entries Open


Recommended Posts

You wont be saying that when you see how good my reverse dohnuts look.

We can stop by macca's and pick up some trays for the rear wheels, Handbags. Then mega hektic slides await! ;)

  • Replies 195
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

hey guys

we need volunteers also to help run the day, so if you got mates who can help out that would be seet as

no volunteers means no fun at all

Crap. This has sold out quicker than I though. I faxed my form in and made payment thinking there was still 5 spots left...end up I'm not even on the reserve list of 12. Now I need to chase my refund. Bugga

So you don't know Amy Parks?

amy-parks-aami-park.jpg

Need some Pre-Deca tune goodness!

Come on Trent, call me back so we can work out a time to tune my baby!

Must. Beat. Tony's. rwkw.

Must. Beat. Matt's. Times.

Must. Avoid. Grant's. Armco.

i am happy to come and be an official if i dont get a spot... i am 3rd on the reserve list and paid, but if i dont get a run, i am happy to come marshall for you guys... That being said, DROP OUT PEOPLE DAMNIT!! :yucky:

So you don't know Amy Parks?

Need some Pre-Deca tune goodness!

Come on Trent, call me back so we can work out a time to tune my baby!

Must. Beat. Tony's. rwkw.

Must. Beat. Matt's. Times.

Must. Avoid. Grant's. Armco.

comeatmebro

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...