Jump to content
SAU Community

Recommended Posts

2004 MITSUBISHI LANCER CZ EVOLUTION VIII

Australian delivered, genuine Km's, Rare leather interior, 1 of 10 delivered to Australia.

Price $30,000 ono *

Colour: Silver

Interior Colour Black

Transmission 5 speed Manual

Body: 4 door 5 seat SEDAN

Drive Type 4x4

Engine: 4 cylinder Premium Unleaded Turbo Intercooled 2.0 L (1997cc)

Reg Expiry Mid March 2013

Road worthy Yes

Kilometres: 110,000

Vehicle ID SSE-AD-434480

Ref Code SSE-AD-434480

Brief Comments Australian Delivered with Leather. GENUINE KM's & service history.

Slightly Modified – See list of modifications

NO finance on this car. Clear on REVS.

*** Sorry NO Swaps ***

Car has full service history by NOTARAS MOTORSPORTS and ESP

All fluids replaced, new bridgestones and tuned October 2012

Power: Very safe tune of 224 KW ATW Tuned by ESP Racing in Canberra on 98 RON. Tuned with open ECU but has ECUTEK LICENCE

  • Oil changed every 5,000 Km's
  • Diff oil changed every 7,500 - 10,000 Km's
  • New Clutch installed March 2011 at 91,500 Kilometres
  • Rebuilt 5SP Gear Box fitted at 85,000 Km's
  • Timing, Accessories and Balance Belt replaced at 79,500 Kilometres
  • New Bridgestone 050’s

Aftermarket modifications include:

  • EVO 9 RS Turbo
  • HKS CAMS 272
  • TOMEI Adjustable CAM Gears
  • Ralliart genuine spark plugs leads, NGK Iridium spark plugs
  • Custom 3 1/2 inch turbo-back system
  • ORC Dump pipe
  • GReedy Inter cooler
  • AVCR Electronic Boost Controller
  • DEFI BF gauges (Boost, Oil Temperature)
  • Walbro Fuel Pump
  • Whiteline rear sway bar
  • Whiteline front sway bar
  • Whiteline Centre Bump and Roll Kit
  • GTSpec under body brace
  • Braided Goodridge Stainless Steel brake lines
  • Ferodo DS 2500 front and rear brake pads
  • Ralliart Accent Plate
  • Blacked out headlights
  • Do Luck Style Front Lip
  • Carbon Fibre exhaust shroud
  • Carbon Fibre canards
  • Volk GTC’s Diamond Black wheels 18x9.5 +12 (poke)
  • Evo VIII Enkie rims - spares

Australian delivered car you will not have trouble getting finance if required and it has genuine Km's

*** Thanks for looking ***

Bad points

2 half crescent minor scratches measuring 10cm on bonnet above both headlights

Pictures up soon

Will give it a tub and take some pics and get em up over the weekend.

I love the leather interior especially the Recaro's as OEM in these.

Can't sell a car without pics. :no:

  • 2 weeks later...
  • 4 weeks later...

PICS UP -> 2004 MITSUBISHI LANCER CZ EVOLUTION VIII

Australian delivered, genuine Km's, Rare leather interior, 1 of 10 delivered to Australia.

$28,500.00

I drive an R32 GTR and this thing pulls like a teenage boy in comparison.

Comes on hard and fast from the get-go. No LAG!

ALL work done by NOTARAS and ESP.

Pics taken this morning.

EDIT: New clutch just put in (December)

Just a few teasers for now

About 200 pics taken last weekend from every angle. Let me know if your keen for more :D

220kws at all 4 running NEW Bridgestone Potenza's 050's A

Without my Diamond black volk GTC's (18x9.5 +12) I'm prepared to take $26.5 k

so it will roll on the Enkie's.

Now up on Gumtree and will go up on Carsales nxt week :thumbsup:

Check out Carsales and compare then check out the cost of importing one.

Is it worth the risk ?? Nah !

This is ADM. 1 of 10 with full leather. KM's are genuine. This ride is genuine.

What you see is what you will buy and it is cheaper and better.

buying 2nd hand highly moddified cars - is a world of worry and expense..........lol

220awkws safely - want to go faster? Yeah can do.

I'll wait right here for you :thumbsup:

Has there been much interest in this sin?

Were the springs and retainers done with the hks cams?

And with the aftermarket cooler, I assume it is just a new core, not piping as well?

Edited by Mitcho_7

Hey MItch - fairly quiet mate to be honest.

I'll check re: springs/retainers and piping question and get back with the answers soon.

Dont know off the top of my head. Matty's car so I'm not over everything like I normally am.

Reminds me I better wash it again :(

Hey MItch - fairly quiet mate to be honest.

I'll check re: springs/retainers and piping question and get back with the answers soon.

Dont know off the top of my head. Matty's car so I'm not over everything like I normally am.

Reminds me I better wash it again :(

No worries.

The cold side pipe looks like its still stock.

Is it running coilovers or still on the stock suspension?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • jeebus. glad you weren't under it while performing the stunt. Also thanks for the link to the wheel measurer, exactly what I needed
    • In the older stuff there were very significant differences 2wd to 4wd, for example Stagea had strut front end for 2wd and double wishbone for 4wd so it was not minor to swap. From poking around the 2wd v37, it *looks* like it might be more possible; some of the parts specifically have "2wd" stamped on them which suggests the platforms are more similar. You'd still want to start with a 4wd half cut to swap stuff from though. I'd suggest if you don't have a tune on the ECU you don't really need one on the trans either. Throttle mapping is in the ECU side (and you can always use a Roar Pedal if you want the throttle to actually respond to your foot), and really if you are happy with the stock power you probably accept the stock trans behaviour too....its all made to be "sporty" not racey.
    • So, updates. I have not washed the car since it came back from Tassie. I've driven it around a bit but not got around to actually sorting it out. I DID raise it because I cracked the rear bar leaving a hotel which was very distressing. Interestingly, the car drives more compliant now that it's raised a fair bit (5mm front, 15mm rear). Also noticed that my FR height was 10mm lower than FL. So that's now sorted out, too. I also bought this and had it printed: https://www.etsy.com/au/listing/1576422240/wheel-and-tire-fitment-tool-universal?ref=shop_home_feat_1&dd=1&logging_key=08f604d9fa4cc383550ba985e6ac85cd5cac7fbb%3A1576422240 Now, if I was smart I would have taken my brake calipers off to actually use this correctly but it was evident enough to me that in the region where the caliper was... there was nothing to hit suspension/guard/arm wise. So I'm going with "it'll be fine" after using the tool to hopefully very precisely measure the wheel clearance. Also while doing this, I had the very VERY bad idea of jacking one of the wheels/suspension arms up while the rest of the car was on jack stands. I did this to see how the arm would travel. This all was well and good until the car slid off the stands and went through a fence. So don't do that. Incredibly nobody was hurt and there was only minor damage to the rear bumper as the car didn't have far to slide, and had 3-4 wheels on it. The only damage turned out to be the fence itself which was easy to fix, and a little bit of damage to the fibreglass rear bumper trim. I had already planned to try a touch up paint kit to fix the time I drove into my garage door to see if it'd help in the interim before I get it fixed properly. I used the Dr Colorchip kit after looking online and seeing everyone talking about it. Yes it's made for chips and not huge broken missing pieces and I'll be 500% recommending it for stone chips after using it for stupid things like me. This took about ... 10 minutes and looking at the half assed photo the 30 second job I did on the bumper corner was almost perfect just by using the tiny little brush and painting it in. The sealact stuff to remove over-painting is really useful, so if/when I do it again I'll likely slather the touch up paint well over it and then clean it up with the cleaning solution. The wheels should arrive in a couple of weeks. I am still kinda confident after doing a stupid amount of measuring (and borrowing a set of 18x10.5+15) that they will not fit because I overlooked something, somehow and flew too close to the sun. ALSO R34 GTR guard liners do not fit on a GTT. I bought the undertray brake duct guides and had the wonderful problem of them not fitting my intake, my oil cooler and the liners themselves were even worse. Attempting to fit them won't work in general - You would have to cut them up as another poster mentioned as the bodywork is different on the GTT. At least I can try to resell them. So instead of cutting those up, I cut up my old already-cut-up GTT liners and extended them by using some PP plastic and drilling some 8mm holes for some nissan clips for the 'extra' bit. Because I was happy to cut them I was able to mount them pretty damn forward so I now have some semblance of guard liners, and the brake vents seal the bumper from the bottom. It sort-of-looks like this, to give some idea - If you look at the GTR and then the GTT this is when I realised that I needed to seriously measure as the inside of the rim area is entirely, entirely, entirely different and could not take any internet measurements for granted.   
    • If you are Ecutek tuned then these TCU tunes are anywhere from $550 to $700 usd. If you are not ECUTEK tuned, then it gets costly!    
    • Sorry to hear your HFM BM57 was faulty,  did you contact HFM I would hope they would be at least grateful for the information if there was some sort of manufacturing fault, you would hope they would be sympathetic even if your item was 2 years old if it had never been fitted. May I ask where it leaked from ?
×
×
  • Create New...