Jump to content
SAU Community

R33 Wreck Silver S1

shy_s6
 Share

Recommended Posts

shy_s6 Veteran

shy_s6

Posted
  • Author
Posted

wheels SOLD

exhaust SOLD

Cusco adj coilovers $650

S1 good condition headlights $280

aftermarket purple fuel rail suit greddy style plenum $50

stock intercooler set up with most pipes $40

gt3076 housings stock front and .63 rear housing $150 the pair

stock dump and front pipes $50

A pillar plastics $30 pair

Manual pedal set up $50

msg me if your chasing anything.

  • 2 weeks later...
shy_s6 Veteran

shy_s6

Posted
  • Author
Posted

r33 rear strut brace $100

r33 silver s2 rear wing $40

r33series 1 headlights no broken brackets not foggy need a polish if your fussy $250

r33 gtst front calipers and rotors $250

aftermarket purple fuel rail to suit rb25 with greddy style plenum $50

r33 A pillar plastics $20 pair

Surge tank round polished single outlet bottom $70 (going duel outlet surge if someone wants to swap?)

stock rb25 cross over pipe with stock bov $20

GT3076 front and rear housings (5 bolt .63 rear) $150 the pair

r33 stock thermo $20

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...