Jump to content
SAU Community

Recommended Posts

short and simple for now as i meant to write this 2 hours ago but procrastinated

basically about two years ago i read the frankiman build over there at the canadian gtr owners club

this made me really desire a gtr and well being 18 and stupid i jumped at the first thing i found

which was my first mistake, it was in terrible condition but i didnt look hard enough.

second mistake was the money i poured into it (no mortgage no family)

ive found myself up creek without a paddle to the tune of about 34k

and well, i couldnt even sell it for 12k, (ive tried)

i am seeking advice in regards to this issue as i have given up and am needing to move on with this chapter of my life

thanks.

Link to comment
https://www.sau.com.au/forums/topic/413946-my-own-little-sob-story/
Share on other sites

Rails dented. Paint is crappy, big patch missing on bonnet. Dash has gauge holes in it. Wheel arches have rust. Skirts have rust.

Not sure about the registerable status but I imagine it wouldn't be a walk in the park. I'm not sure about the accident status. Looks quite straight but the rails suggest it has gone over an end or just been jacked up wrong

Rails dented. Paint is crappy, big patch missing on bonnet. Dash has gauge holes in it. Wheel arches have rust. Skirts have rust.

Not sure about the registerable status but I imagine it wouldn't be a walk in the park. I'm not sure about the accident status. Looks quite straight but the rails suggest it has gone over an end or just been jacked up wrong

Hmmm, your best bet is to just find a clean, straight registerable shell, transplant everything, then sell it off.

Or get the current car registered then sell it off.

A local panelbeater had a car there with dented rails. His Tech teacher friend was inspecting it, so yours truly has a squizz.

The teacher said that the rails can be boxed or the cheaper way was to drill a hole in each rail > thread it > insert a bolt > pull the bolt down.

How did you pour 34k into a car without noticing any of the issues before hand......if they were as bad as you say they were.

Most things can always be fixed/Restored if you have the time and funds to do so.

In your situation maybe best to cut your losses instead of chasing that 34k back. As above i'd pick up a shell a transplant it all. if you poured your money into engine, and other bolt ons. Then just call a 3k shell and expensive lesson.

How did you pour 34k into a car without noticing any of the issues before hand......if they were as bad as you say they were.

I can see how he's done it but I would have looked a bit better first.

if hes bought EVERYTHING on the car new then its certainly doable. I have $10k in mine before I refit the steel panels and paint it. that said I did buy most of the bits new for it.

Most things can always be fixed/Restored if you have the time and funds to do so.

yep! patience is a virtue especially if you own the place where it is stored for a few years.

In your situation maybe best to cut your losses instead of chasing that 34k back. As above i'd pick up a shell a transplant it all. if you poured your money into engine, and other bolt ons. Then just call a 3k shell and expensive lesson.

given he has lost patience with it - I would certainly agree.

Hmmm, your best bet is to just find a clean, straight registerable shell, transplant everything, then sell it off.

Or get the current car registered then sell it off.

i feel the current is far from being able to be registered. it was imported under the 15 year old rule before that was axed and an engine failure meant it never was registered first

You could part it out....

i dont think itd be worth all that much like that?

A local panelbeater had a car there with dented rails. His Tech teacher friend was inspecting it, so yours truly has a squizz.

The teacher said that the rails can be boxed or the cheaper way was to drill a hole in each rail > thread it > insert a bolt > pull the bolt down.

once the rails are done there are all the other imperfections too, shell seems the way to go

He would get more money for his time if he parted it out

How did you pour 34k into a car without noticing any of the issues before hand......if they were as bad as you say they were.

Most things can always be fixed/Restored if you have the time and funds to do so.

In your situation maybe best to cut your losses instead of chasing that 34k back. As above i'd pick up a shell a transplant it all. if you poured your money into engine, and other bolt ons. Then just call a 3k shell and expensive lesson.

had the car for 2 weeks before i sent it off for engine rebuild, didnt see it again for a couple of months,

i will be going down the shell line, its the most sensible option

I can see how he's done it but I would have looked a bit better first.

if hes bought EVERYTHING on the car new then its certainly doable. I have $10k in mine before I refit the steel panels and paint it. that said I did buy most of the bits new for it.

yep! patience is a virtue especially if you own the place where it is stored for a few years.

given he has lost patience with it - I would certainly agree.

patience comes and goes with it haha, sometimes i am in the mood, other times i really just want it gone

swapping into a clean shell is the way to go i feel, one last hit at it and hey i might even find love for it again

Transplant or part out. Once the ralis are damaged, As far as I know the system its a statutory write-off.

It might not be on the WOVR register yet, but when someone goes to get it pink or blueslip for rego the red flags will start flying.

Edited by badben

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...