Jump to content
SAU Community

Recommended Posts

Im with Wolverine. Like Button Kimi is the other WDC guy you can throw in a car and not upset a slightly more prexious driver. Just like Kimi would be good at RBR with Seb I think it will work at Ferrari. I think you will see just how amazingly on it Alonso always is....he rarely mises a trick

I am gutted for Lotus. Hulk may be a good signing for them but he wont bring the sponsors, coverage and talk of the team which seems to critical to it at the moment for funding and potential for increased Renault dollars and solid future campaigns :( I hope my buy Romain keeps his seat and they dont sign Julk then go for a funded 2nd driver :(

GUTTED!!!!

Lotus said earlier that if Kimi leaves that would help Grosjean keep his seat for 2014 as it would give them some continuity.

I hope Hulk does not sign for Lotus. He'd be better off waiting for a better seat. It will only take a year for two or three top seats to open up I reckon. Keep over-performing in the Sauber for one more year. Don't sign to the team that's only fast in one particular set of conditions and barely has money to pay their drivers.

Eddie is predicting there will be a fernando to mclaren move in 2015

http://i3.kym-cdn.com/entries/icons/original/000/000/854/vader_NOOOO.jpg

Wonder what this is based on? Honda being at Mclaren in 2015?

At the moment don't really see a reason why he would want to leave Ferrari UNLESS Kimi starts dominating there

Given the problems he previously had there and how happy he seems at Ferrari, its a bit strange to me

That describes Sauber.

ok - no point signing to the other team that's only fast in one set of circumstances and can't pay their drivers.

still better off waiting for those top two or three seats to open up imo than locking into Lotus.

Edited by hrd-hr30

ok - no point signing to the other team that's only fast in one set of circumstances and can't pay their drivers.

still better off waiting for those top two or three seats to open up imo than locking into Lotus.

Problem being if you wait you get overlooked. There will presumably be an opening at McLaren when they get sick of Perez being hopeless but I reckon Hulk should be worried about Sauber dumping his arse for a pay driver. Happened to him at Williams and I reckon it could happen again. He would have been alot better off staying with Force India.

But for now he should sign for Lotus. It will be quicker than next years Sauber and he will only have Grojean to beat.

ok - no point signing to the other team that's only fast in one set of circumstances and can't pay their drivers.

still better off waiting for those top two or three seats to open up imo than locking into Lotus.

Lotus is beating Sauber easily this year, a step forward is still a step forward. It's not like he's going to sign a 10 year contract with Lotus. A 1 or 2 year deal would be fine if he wanted to move to one of the more established teams later on

The thing is, most drivers only get one shot at a drive for a major team. Don't blow it on the wrong seat. Lotus is the wrong seat.

Kimi/Alonso is bound to blow up in their faces with one bloke leaving or being dumped.

Perez is unlikely to be re-signed by McLaren imo. Button's getting a bit long in the tooth as well.

RB young driver program is normally very quick to dump drivers if they don't instantly live up to expectations too. Although we are in uncharted teritory as to how long they give a young gun in the main team.

Plenty of good seats could be coming up in 2015. And by then the drivers will have an idea of the pecking order of the new cars & drivetrains.

Edited by hrd-hr30

and then get forgotten about like Perez at McLaren. No other top team will be looking at him. Nup, you've got to make your move to a top team count. Don't waste it on Lotus.

Edited by hrd-hr30

and then get forgotten about like Perez at McLaren. No other top team will be looking at him. Nup, you've got to make your move to a top team count. Don't waste it on Lotus.

You have to beat your team mate. Perez is forgotten because Button is quicker than him. And Button is past his best so it doesnt reflect well on Perez.

You are also assuming Sauber have the funds to develop a decent car next year. Which is a courageous assumption. If he stays with Sauber and the car is a dog then what hope will he have?

Hulk would get beat by Romain...but I am biased :) I think Monza was the first time I have not seen Hulk throw the car away or do something stooooppid when in a good spot. Not saying romain is anyworse, but he has had loads of races where he has shown amazing wheel to wheel race craft...sadly its often punctauted by poor clashes that detract from his good races. Was it Korea of India last year where he had some amazing battles with Shcuey and others?

Fernando Alonso pocketed in the region of $30million last year, making him the highest paid driver in motorsport in the latest Forbes rich list.

The Spaniard's current deal with the Italian team runs until the end of the 2016 season, but it remains to be seen if his new team-mate Kimi Raikkonen, who will rejoin from 2015, will make the list next year as he is rumoured to have signed a $20m per annum deal.

Full list:
1. Fernando Alonso F1 - $30m (salary/winnnings $28m; endorsements $2m)
2. Lewis Hamilton, F1 - $27.5m (salary/winnnings $26m; endorsements $1.5m)
3. Dale Earnhardt Jr, NASCAR - $26m (salary/winnnings $13m; endorsements $13m)
4. Jimmie Johnson, NASCAR - $24m (salary/winnnings $17.3m; endorsements $6.7m)
5. Valentino Rossi, MotoGP - $22m (salary/winnnings $12m; endorsements $10m)
6. Tony Stewart, NASCAR - $18.5m (salary/winnnings $12.5m; endorsements $6m)
7. Jeff Gordon, NASCAR - $18.2m (salary/winnnings $12.7m; endorsements $5.5m)
8. Sebastian Vettel, F1 - $18m (salary/winnnings $17m; endorsements $1m)
9. Danica Patrick, NASCAR - $15m (salary/winnnings $6m; endorsements $9m)
10. Jenson Button, F1 - $14m (salary/winnnings $14m)

http://www.planetf1.com/driver/18227/8917157/Alonso-still-motorsport-s-top-earner

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...