Jump to content
SAU Community

Recommended Posts

  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yeah... a 10cm distance :whistling:

Usually don't have someone hooking under the arms, just ready to assist with the bar shadowing it. When I used to do squats years ago in a supervised environment we were just instructed to drop them, never got assisted. Wrong or down to preference?

Although that was a while ago, could be mixing up the dropping with deadlifts. My memory is terrible.

Edited by JEPPE

down to preference i believe. i've read people say (actually over in the gym thread here haha) that if you're going on heavy weights (where you might have difficulty) then don't use the collars, so that if you really are in trouble then just tip over and drop off the weights. remember that the bar will swing up though haha

^^^ That's only with Benching.

If you're squatting by yourself, you really should be doing it in a power cage with the safety bars there to prevent you crushing yourself or damaging the bar.

You can't spot a squat by shadowing the bar.

unless you want to hurt yourself and the lifter.

Edited by TTT

I suppose it wasn't spotting as much as it was assisting, I get what you mean though.

Have seen people using the cages before, sometimes they seem to do it at obscure angles though. Is it meant to be used as if squatting without a cage?

in a proper comp, you have spotters on either side of the bar too.

Their job is to help lift the bar.

the spotter behind is there to keep the lifter from falling or folding over etc.

Charlie - the safety bars can be removed.

you can do everything in there as the pin height where you put the bar has many heights.

Most of those cages will also have chin up handles on the top and some have dipping bars on the side.

That's why they are great for home gyms.

you get a power cage, a bench, barbell and weights and you can do 99% of what you need.

the best technique in heavy squatting is to have no spotter behind you, and if you fail you just throw the bar behind you.

It's the safest and easiest, and means you don't need a power rack or a spotter to squat to failure.

the best technique in heavy squatting is to have no spotter behind you, and if you fail you just throw the bar behind you.

It's the safest and easiest, and means you don't need a power rack or a spotter to squat to failure.

I honestly can't see how it's possible to get the bar to fall BEHIND you on a squat that you failed due to being unable to lift it.

If you squat high bar and can keep your torso upright, it will be easier to dump the bar behind you.

Low bar and wider stance has you leaning forward more.

That would be hard to dump the bar behind you.

Also depends where in the lift you fail.

If your hips raise faster than your torso (bad form or fatigue etc etc) you'll end up in a good morning type position and you won't be able to dump the bar behind.

If you squat high bar and can keep your torso upright, it will be easier to dump the bar behind you.

Low bar and wider stance has you leaning forward more.

That would be hard to dump the bar behind you.

Also depends where in the lift you fail.

If your hips raise faster than your torso (bad form or fatigue etc etc) you'll end up in a good morning type position and you won't be able to dump the bar behind.

Yeah I was thinking this.

Plus I'm in the mindset of low bar anyway, high bar is uncomfortable as all shit for me.

I honestly can't see how it's possible to get the bar to fall BEHIND you on a squat that you failed due to being unable to lift it.

let go of the bar and move forward. Maybe easier with a high bar upright squat but unless you are good morning the squat for some reason it's easy to do with a low bar squat too

Or you could squat in a rack/cage that has safety bars and ass to ground it onto the bars if you can't lift it...

I hate squatting in a cage, everything is so close and i get a bit claustrophobic.

Outside is fine, it shouldn't be that often that you are failing on a squat in training anyway

the best technique in heavy squatting is to have no spotter behind you, and if you fail you just throw the bar behind you.

It's the safest and easiest, and means you don't need a power rack or a spotter to squat to failure.

provided you have bumper plates and a floor that is okay to drop weight on

when at commercial style gyms I squat with no spotter and no safety bars... then you have no choice but to make the lift... you'd be amazed how a bit of panic/fear can help you out of the hole lol (don't do this with 1RM attempts obviously)

provided you have bumper plates and a floor that is okay to drop weight on

when at commercial style gyms I squat with no spotter and no safety bars... then you have no choice but to make the lift... you'd be amazed how a bit of panic/fear can help you out of the hole lol (don't do this with 1RM attempts obviously)

I know, that's why i never squat with spotters or a rack.

I guess if you can't drop the weights then use a rack i guess. Spotters are useless imo for squatting when training

Markos posted this on another forum... a must read for girls (make sure you read the last couple of pages)

http://startingstrength.com/articles/training_perspective_gillian.pdf

"In Mark Rippetoe’s words, “Your appearance when fit is almost entirely a result of your genetics,

which are expressed at your best only when your training level is at its highest, and this level is only

obtainable from a program based on an improvement in your performance, in the gym or on the

field. And the best improvements in the gym occur when participating in a program that looks more

like performance athletics – the kind of training done by competitive athletes – than one that looks

like waving your arms and legs around on a machine or slowly rolling around on the floor” (Strong

Enough?, p118)."

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...