Jump to content
SAU Community

Recommended Posts

I've got an r32 coupe project car that I'm thinking of letting go if the right offer comes along.

its wine red.has a fuel setup in the boot.5 speed manual no crunches when shifting or anything.

has an rb20det with it that just needs to be installed. and also half an rb20, (block,crank,pistons,head)

all you need is a front bar and bonnet and put together then rego....

17 inch BBS on the front and 16 inch r32 rims on the rear.

will come with a mines ecu, stock coil packs, op6 turbo off an r34 gtt( was told it has been hi flowed but nfi ), stock rb20det turbo.some other parts sitting in the boot.

willing to swap for a daily with rego but only manual.

LOCATED IN QLD i will not deliver, u pick it up.

depending on how long it takes to sell i may have the front bar and bonnet situation sorted.

i just don't have the time or money to finish it as have returned to studying.

advertised elsewhere

make an offer.

no lowballing thanks.

will take $3500

mob 0468 719 321

Untitled.png

2011-12-15134118-1.jpgodo1.jpg

2011-12-15134222.jpg

Edited by jaffadrifts
Link to comment
https://www.sau.com.au/forums/topic/414593-r32-project-up-for-grabs/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...