Jump to content
SAU Community

Recommended Posts

my daily might not be so daily now....

twin 40DCOE webers

290/295 cams with .453 lift

spool rods

20" over bore pistons

11.63 compression

dual valve springs

roll master timing chain and sprockets

GTRsean special modded sump.....yet to be proven.

the original flywheel has gone from 7.25kg to 5.5kg.

exedy heavy duty clutch.

electronic optical ignition conversion, using 7M coil.

post-38774-0-62454900-1355347391_thumb.jpg

post-38774-0-95483100-1355347514_thumb.jpg

post-38774-0-94289500-1355347777_thumb.jpg

post-38774-0-98068300-1355347858_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/415505-toyota-ke55-4kbecause-race-engine/
Share on other sites

Check that sexy guy out!! :P

Oh and these engines are single cam, pushrod, non crossflow alloy head.

Cam will be on from 3500 to 7500RPM from memory. Can't go over 8000 for long periods of time as the blocks tend to crack haha....

Considering that the standard 5K that was in it put out 47 RWKW with the carbs slapped on and the existing 4 into 1 headers....I'm scared.

Still no brake or suspension upgrades yet......how not to do up a car, but makes you feel more alive :woot:

  • 4 weeks later...

When you said heavy duty clutch I imagined 2 bits of brown bread rubbing together!

Can't wait to see/hear the new motor up and running. Will need moar handling for sure!

close, it's slipping already. acts like a turbo but with none of the power. I am trying to organise it to be freighted from Sydney to Brisbane.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...