Jump to content
SAU Community

Recommended Posts

Hi i have a nitto pump in my rb25 with crank coller i removed the inner spring in the pump because i thought the extra pressure would give me oil problems I was advised to restrict the oil to the head which led to lifter and cam failure I removed the restrictor and used the standard restrictors with new hyd lifters and new cams and 5000kms later have had no problems and allways have good oil pressure i also add an extra 500mls of oil at oil changes.

Are you not emptying the stock sump running a high flow pump and with no restritors? Do you have any other oil control?

I've been told a nitto pump would empty a 6.5l and I should get a 9l and mine is only a street car not drifter or track or anything

How is yours going for oil pressure with the inner removed?

My engine builder has removed the inner spring and added a shim...

My restritors are block centre, 1.5mm rear I believe!! The car is just a street daily driver will see street pulls and boost here and there

So you have a nitto pump and have left the standard restritors in?

And not having any oiling problems?

I was gonna get a 9l sump made up as I was even told that in one case a guy had a nitto pump on standard sump and empty the sump in 40secs at full throttle... Was also told 6.5l wouldn't be enough :/

I have an N1 Pump with Billet gears. The engine is not fully assembled yet so no results/answers from me

The oil that would run to the back of the head would be the oil thats passed the lifters/cam journals and is running back down, the pressure side of the galleries would be changed minimally with G's

Yeah Pressure accross all areas should be equal so shouldnt be an issue till it becomes low pressure. Last time I looked the oil feeds go up one of the head bolt holes so wasn't really sure where the pressure went from there, but it makes sense now that I actually think about it. The head cant be splash lubed, dont know what I was thinking lol.......

Yeah Pressure accross all areas should be equal so shouldnt be an issue till it becomes low pressure. Last time I looked the oil feeds go up one of the head bolt holes so wasn't really sure where the pressure went from there, but it makes sense now that I actually think about it. The head cant be splash lubed, dont know what I was thinking lol.......

Yeah, feeds the galleries :happy:

I think its on one of your other threads but tomei pump set 65-70psi hot, 2x 1.3 restrictors (I recon they crushed to 1mm) running redline 15w50 oil, enlarged return galleries and drilled returns to 9mm rear head drain/vent, made my own sump, baffled and gated holds about 7-7.5L.

Catchcan I made up, returned to sump..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...