Jump to content
SAU Community

Recommended Posts

Yh the top half is good but the bottom half is kaput, has a cracked piece.

Hmmm... Wouldn't mind the top piece and maybe the throttle body too, I wanna get a larger throttle body (KA24) and bore out the inlet where it bolts on for more airflow.

Praps I can get it from you soon. (When I reclaim my O2 socket) ;)

Anyone know where I can get an aluminium 3/8" NPT bung and a plug for it?

Going speed density soon on the evo and wanna get one welded into the cooler piping for the IAT sensor.

Also need a plug to block up one of the post cat o2 sensors I'm not using in the new exhaust.

Any suggestions on where to pick up either of these items would be greatly appreciated!

f**ked around with my idle speed, cranked it down so the timing belt doesn't f**k me off, sould have it booked into Trojan next week :)

and I got the GTR bov on, haven't been out to see how it sounds yet :( that was hard! the guy before me had a bigger bov on so he clamped the bigger hose down heaps, so it was all deformed, after a lot of heating and swearing I finally got it on :D

me : 1 - bov : 0

Edited by ..::R33GTS-T::..

Anyone know where I can get an aluminium 3/8" NPT bung and a plug for it? <br />Going speed density soon on the evo and wanna get one welded into the cooler piping for the IAT sensor.<br />Also need a plug to block up one of the post cat o2 sensors I'm not using in the new exhaust.<br />Any suggestions on where to pick up either of these items would be greatly appreciated!

<br /><br />Pirtek in Fushwick or Industrial Supplies in Fushwick opposite shell. To get it welded I would do it for you just have to find time to sneak into my uni workshops otherwise if your in a rush Natrad (Phillip) can tig weld.

Engine bay is actually FILTHY!!! It had spider webs near the oil filter.

Needs a good clean but so does the whole car...Meh. I'll get there. :P

Made some enquiries regarding Exhaust, Wheel alignment and Rego Inspection today...

Still a work in progress.

Engine bay is actually FILTHY!!! It had spider webs near the oil filter.

Needs a good clean but so does the whole car...Meh. I'll get there. :P

Made some enquiries regarding Exhaust, Wheel alignment and Rego Inspection today...

Still a work in progress.

you could almost say your engine bay is cleaner then mine :( looking at those photos made me go out and clean my engine bay! haha its defiantly coming along nicely :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...