Jump to content
SAU Community

Recommended Posts

Norton written off??? Nooooooooooooooooooo...

Dunno the history but this car used to be parked out the back of my work in Belco daily about 5-6 years ago.

Was owned by a Computer Geek?? Asian fella.

Loved looking at it everyday. Was a Gorgeous Black R32 GTR with vented Bonnet. I'm drooling now!!!

saw it maybe 2 years ago in Mitchell near Gentech.

I have pics...

post-78856-0-17688100-1355914506_thumb.jpgpost-78856-0-17217800-1355914559_thumb.jpgpost-78856-0-18292500-1355914573_thumb.jpgpost-78856-0-98470600-1355914581_thumb.jpg

Edited by Not a Pulsar

Well it's a repairable writeoff that is at Pickles. Looks like some serious side and rear end damage. Going halves with a mate depending on cost.

Looks like plenty of bolt ons. Will be having a closer look tmw AM.

Thanks for the pics and replies, it has awesome wheels on it now that would look good on my firdy free but I assume one is cactus.

Cheers

This is the one a pickles right now. I'd never seen it before about 4 months ago when I noticed it parked in the back lot of Pedders in Phillip. Either rear left or rear right (can't remember exactly lol) looked like it had hit a gutter at speed sideways coz the wheel looked like it had about 40 degrees of positive camber. Was there for ages just sitting so when I heard it had ended up at pickles I just assumed that they were assessing the damage.

Hope this helps

The car was pretty rough. A lot of the visible GTR specific stuff had damage or wear. The only thing that looked neat were the seats.

- The original Aluminum bonnet had been cut and vented instead of an entire aftermarket job.

- GTR front bar was damaged

- GTR rear wing was damaged

- GTR front guard was damaged

- GTR rear guard was damaged

- Oil leaks from engine somewhere.

- GTR cradle mounts were broken

- Control arms were bent

- PowerFC hand controller was missing

- Coolant was low or not there

- Dash appeared to be broken or tampered

At that point I bumped into a mate who said they were going to bid more than I was and stopped up looking.

I wondered why it was also not bought back. The damage from the crash was not bad, probably fixed for about 4.5k in a shop. It didn't look stolen/recovered (had an alarm and assumed immobiliser installed), so it was most likely "driven" into the crash. It appeared to have some goodies installed too like the PowerFC, maybe upgraded injectors, had different fuel fittings, an oil cooler, massive exhaust, aftermarket FMIC.

I think fixed, it should sell for at least 12k. I was going to wreck it down with a mate if it was in our price range.

Anyway, I do wonder if my mate bought it. I might try to find out tomorrow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...