Jump to content
SAU Community

Recommended Posts

So keen to see the suspension work happen! Can't wait ants!
me too Zac. However after speaking with Gary aka sydneykid it will be a nice package for sure. But it ain't cheap so I'm in saving mode FTM but in a few weeks we will see some suspension drool ;)

Today was a big day and got lots done.

First up the rear wheel arch got some TLC

post-5053-13955676560444_thumb.jpg

post-5053-13955677177786_thumb.jpgsmoothed out all the dodgy spot welds

post-5053-13955677657172_thumb.jpgthen I filled in the gaps with some selleys autofix to ensure no rust decides to set in

post-5053-13955678763059_thumb.jpgpretty handy stuff

Then preparation time.

I wiped the wheel arch with some prep wash to remove any dirt and grease

post-5053-13955673938851_thumb.jpg

post-5053-13955674381787_thumb.jpg

Then more preparation work

post-5053-13955683170533_thumb.jpg

Got my big trusty making tape out and.....

post-5053-13955683834138_thumb.jpg

neatly taped around the wheel and inside the wheel arch as well

post-5053-13955684564229_thumb.jpg

Then I attached some newspaper to protect the inside from any unwanted paint spatters. I also covered the rear brakes with an old work shirt that I no longer use

post-5053-13955685255908_thumb.jpg

Now we are ready for painting :)

post-5053-13955686200881_thumb.jpg

I acquired this paint can from super cheap and is the recommended paint for Nissan between 1984 onwards

post-5053-13955687441745_thumb.jpg

Nissan crystal white yeah

Next step was to get RHS N1 side-skirt back on

post-5053-13955700793458_thumb.jpg

Photo of corrected bodywork without side-skirt just for the hell of it

post-5053-13955702885554_thumb.jpg

I then gave the side skirt a quick wipe down from all the dust it had gathered the past few months and then applied som Sikaflex

post-5053-13955703892654_thumb.jpg

post-5053-13955704060028_thumb.jpg

Next I gently made sure I put the side skirt back to where it belongs

post-5053-13955704807353_thumb.jpg

On the car ;)

post-5053-13955705047569_thumb.jpg

Again I used clamps to ensure the side skirt sits flush against the car

post-5053-13955705658852_thumb.jpg

The excess Sikaflex will eventually just be peeled of after it's dried

post-5053-13955706232086_thumb.jpg

Like so

post-5053-1395570664817_thumb.jpg

The car is finally starting to come back together

  • Like 1

I also thought I would take the opportunity to follow a trend happening with some builds FTM

post-5053-13955707909685_thumb.jpg

and detail the inner door cards with

CARBON VINYL WRAP!

Do first up

post-5053-13955709592798_thumb.jpg

Clean you're door card as it has collected a fair bit of dust over its time

post-5053-13955710058767_thumb.jpg

Then unscrew the back of the inner door pocket

post-5053-1395571058811_thumb.jpg

Make sure you don't remove the factory glue at the bottom of the inner door pocket card

post-5053-13955711259608_thumb.jpg

I got hold of some 3M carbon vinyl wrap from eBay for about $36 but you.can get it from super cheap about the same price the length I got it for

post-5053-13955712998176_thumb.jpg

Then just measure and apply carefully

post-5053-1395571331604_thumb.jpg

You do not need to cover the entire infer door card as the edges are not visible with the inner door card

post-5053-13955714085519_thumb.jpg

I also wrapped the side open edge for more strength but is not mandatory

post-5053-13955715102579_thumb.jpg

Then just bolt everything back up and admire you're work

post-5053-13955715908051_thumb.jpg

post-5053-13955716055043_thumb.jpg

That's it for now.....more to follow soon :)

  • Like 1

Lookin good mate, seeing how good yours has come up is encouraging me to clean mine up, so thanks :)

Also another door card win. Definitely a cool craze happening ATM, I will be doing this too lol

Just few more pics of before after bodywork / body kit correction just the hell of it

Thanks for putting up how you did your side skirts. Give me a much better idea how to do mine, come time!

Fantastic work.

Looks so much better!

  • Like 1

Thanks for putting up how you did your side skirts. Give me a much better idea how to do mine, come time!

Fantastic work.

Looks so much better!

No worries Shivam. That is what its all about ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...