Jump to content
SAU Community

intercooler question

Josh. H

By Josh. H,
in Queensland

 Share

Recommended Posts

krawler Mentor

krawler

Posted
Posted
Hi guys just a qick one for the 32 owners who has put a front mount on theirs and what difference did it make if any. Im still debating if i should put one on my 32. Cheers guys

(1) FMIC is going to make a very small gain if thats the only mod you do

(2) FMIC will allow you to run more boost (up to the level supported by your fuel system and turbo and pistons obviously)

(3) We got more power gain from the FMIC than from the AVCR or PowerFC simply because we could run more boost safely. Better tune at same boost levels != making good power.

y0.

SHY32 Collaborator

SHY32

Posted
Posted

Josh...I just had the piping done on my r32 yesterday so am off getting it tuned today...i dont have any big mods apart from that so i'll let you know how it goes, im not expecting much tho :D

you can pick up hybrid coolers 600x300x76 (i think) pretty cheap these days and i have a mate who can source a cooler and also does piping so if you need a referral pm me

Syl :P

chaos Grand Master

chaos

Posted
Posted

you can also talk to wados..hes gettin a frount mount on his done and he's got exhaust and some other decent mods done....im sure he would be willing to give you some pointers..also remember cheap kit can = cheap quality you dont want something thats not gonna do its job right....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...