Jump to content
SAU Community

Recommended Posts

Adam - that's nice average power.

When my R33 was stock I get 145 rwkw with just a zorst & pod.

So 162 with auto is pretty good, I'd say. What is the boost set to ?

What does the seat of your pants say ?? Can you feel the difference ??

Meggala,Yeah I am. I can feel that flat spot but I haven't had a chance to drive it properly yet since the AVC-R went in on friday. Makes me wonder about all these guys with 200 and 250 rwkw though.

Obviously I know that I have an auto and there are power losses there but that was my choice for comfort in Sh!tney traffic.

Here are my first dyno sheets.  Car is an R34 GTT auto with full exhaust and AVC-R boost controller.

 

What do people think?  Is this alright?

looks good adam. with the tiptronic gearbox i think you should be reading slightly higher than manuals because of gear ratios. and i also believe auto/tiptronics have a different ecu....but dont quote me on that :P from memory (i'll have to dig it up) i got 154kw on the same dyno with about the same amount of mods.

1 tip - FMIC. i didnt notice any seat of the pants difference and thus that represented zero bang for dollar!!! for a street car, i think the side mount is perfect for power levels close to 200rwkw. when you do some trackwork or get a bigger turbo then i think this is where a FMIC starts to get important.

spend your money on a handling pack from say whiteline. what are you after? track stuff? street?

3rd gear for me and 4th for you is 1:1 but I'm not sure if this takes into account the diff or not.

I do like the track which is why I thought about getting the FMIC. I'm also leaning towards whiteline for suspension.

I've got to get some decent tyres too.

Robo: Yeah they certainly seemed to wring it's neck on the dyno didn't they. I went to 7k last night when I miss pressed the button to change into 2nd gear. It didn't seem to hit any rev limiter.

Franks: I was going from memory but I think it touched that mark once at Eastern Creek. The rest of the time it stay a little under that even after 15 minutes on the track. It behaves so well. Brakes never fade, never overheats, once got at A/T light to go on but that was at the end of a track session with the last two laps basically being drift laps at Wakefield the other day.

Benm: seems it took 5.5 hours :)

I had a proper drive last night and that flat spot is quite annoying but the rest of it... mmmm... power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...