Jump to content
SAU Community

Opinions on 1st dyno r34 GTT

Abo Bob

By Abo Bob,
in Engines & Forced Induction

 Share

Recommended Posts

Abo Bob Grand Master

Abo Bob

Posted
  • Author
Posted
Hi Abo,

So what do you think of the tiptronic transmission?

I'm thinking of selling my R32 and getting an GTT.

But the only ones available on the market right now are autos... (I'm from Malaysia)

Any thoughts?

How does it perform on track day?

I like it. I always use the tiptronic buttons and it's quite enjoyable. It took a month or two to get used to it but I'm fine now. It's good on the track too. I've been a couple of times. One thing I guess is that it sucks a few extra kilowatts from your motor so you need more for the same level of performance and also engine management is not so clear cut. Manuals you just buy a PFC and that's that. The only thing I think I can reliably use is the Greddy emanage.

Haven't got to that yet though.

666DAN Grand Master

666DAN

Posted
Posted

Your AFR’s have lots of potential from about 5000rpm, you look a tad rich there. (When my coils actually fire) My car really hammers at 5000rpm to redline. E-manage is a piece of piss to tune, especially if you’ve already had a dyno run and can back calculate the required duty cycle based on your current injector cycles and the AFR readings.

Yotis Experienced

Yotis

Posted
Posted
I like it.  I always use the tiptronic buttons and it's quite enjoyable.  It took a month or two to get used to it but I'm fine now. It's good on the track too.  I've been a couple of times.  One thing I guess is that it sucks a few extra kilowatts from your motor so you need more for the same level of performance and also engine management is not so clear cut.  Manuals you just buy a PFC and that's that.  The only thing I think I can reliably use is the Greddy emanage.

 

Haven't got to that yet though.

You use the bottons on the track abo? I find the buttons a pain the back side.. but then again the track that I went on has a few twisties. :thumbsup:

The triptronic gearbox definitely suck quiet a few extra kilowatts tho.. :) But more fun..

Abo Bob Grand Master

Abo Bob

Posted
  • Author
Posted

ed: I wish.

Yotis: Use the buttons all the time mate, that way when you are on the track you will be in sync with your car.

I was out on Wakefield which is quite twisty the other day and had no problem using the buttons.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Who has a Infiniti Q60, Q50 (V37)?

      By MBS206 · Posted

      Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      PXL_20250828_063541093.TS.mp4
×
×
  • Create New...