Jump to content
SAU Community

Recommended Posts

hey guys,

i have a bit of a problem, my gear shifting is getting really notchy, and makes it weird to put into gear sometimes. its not to the point were it grinds , its sometimes just hard to get into gear, but if u dont push the clutch all the way in to the floor then it rumbles through gear changes a bit. i went to one place that said that my syncros are screwd and that i would be looking at like $1500 to fixit at least, it doesnt fall out of gear or grinds that bad so i dont think this is the prob.

its not consitant either, sometimes u can drive it fine and other times it will stuff up.

the reason that i am posting this in here is to find out if any of you know of a good place i can go to on the gold coast that is reasonabley priced and knowledgable, so i can get this prob checked out and fixed?

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/
Share on other sites

I recommend changing your gearbox oil with some Redline Gearbox Oil.

You may find that this will fix the problem for you..... out of interest when was the last time the oil was changed?

If you don't know then it is time for you to change it.

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854078
Share on other sites

i knew someone would ask, about a month ago..........lol, yeh it didnt help much, i was given some of this nulon aditive stuff that is supposed to help but i cant see how it would.

i think its a clutch prob hey, not the actual clutch just how it engages and dis-engages.

any places to go and c about the prob?

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854091
Share on other sites

After having a clutch replaced no too long ago, I asked my mechanic about a similar (slight) crunch going into 5th. My concern was gearbox but he mentioned that the parts quite often become glazed after prolonged use and recommended running a deglazing compound with the oil for approx 1 week, then change back to your regular oil. Apparently this usually does the trick.

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854096
Share on other sites

i have this prob, i replaced clutch month ago apparently it needs adjusting and now i have this prob on load and quick shifting 3-4th will grab before hitting 4th gear, spoke with machanic apparently redline might fix ill let ya know if it fixs the prob...else was told that sometimes little metal pieces falls off the syncros and when ya change gearbox oil it comes out but it doesnt explain how lubrication will fix the problem...but ill let ya know how i go b4 ya spend big dollars on getting it fixed..

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854134
Share on other sites

cool, sounds good man, actually your prob sounds similar to mine but i dont think my oil change helped much, and a few months back a mechanic drove my car and said that the clutch is good but just needs adjusting,so we will see what happens, i hope its nething but the need for a new box or reconditioning.

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854144
Share on other sites

I had a similar problem, could not get from 2nd to 3rd without crunch. But not always. Felt notchy etc. Was told the syncro story as well. Turned out to be clutch adjustment and bleeding not done properly. Apparently there is this extra drain line in the clutch bleed system and some air can get into it. Weird Nissan thing. Guys at ABS Sumner Park fixed it.

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854323
Share on other sites

Just another look at the situation, I've got a short shift thing in my car and "apparently" (don't take it as gospel), the synchros dont keep up when changing gears making them crunch. I know andrew changes gears faster than me and he crunches them. It's normally 5th that crunches. We find that if you leave it like 1-2 seconds before putting it into gear it doesn't crunch.

Just another idea.

My gearbox was starting to crunch heaps before I got the clutch replaced. Once I got the clutch replaced it stopped.

Link to comment
https://www.sau.com.au/forums/topic/41705-gearbox-problem/#findComment-854674
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...