Jump to content
SAU Community

R33 Gtr Pull Type Clutch Failure

GTR260
 Share

Recommended Posts

GTR260 Proficient

GTR260

Posted
Posted

Soo I bought a reputable brand clutch 400kw single plate less than 3 months ago & had it fitted by a reccomended workshop on this forum, all was fine untill the other night.

Went to change gears and peddle went straight to the floor & couldn't select any gear, got under the car and inspected and found that the throw out bearing had separated from the pressure plate, is this a common problem with pull type clutches? What would usually cause this failure? Just asking for opinions.

Spoke to the clutch manufacturer and the said the see this issue a fair bit and that it's cause by ppl letting the transmission hang from the clutch during re installation. The asked me to take it in to them so they can inspect it,

Hopefully they will warrant it as I don't want to spend another $1600 on a clutch for it to fail again.

If it is the installers fault then I hsve fat chance of them covering it as they seem to have closed their business

Link to comment
https://www.sau.com.au/forums/topic/418076-r33-gtr-pull-type-clutch-failure/
Share on other sites
luke gtr Grand Master

luke gtr

Posted
Posted

Not good mate.

even hanging the box, I wouldn't expect this.

generally, you put the box up, then engage the bearing.

its pops in, but can't come out.

unless the clutch had it in to begin with, not many do.

keep us updated.

tricstar Mentor

tricstar

Posted
Posted

obviously it shouldn't pop out, but maybe the clip was damaged on install? will be obvious when inspected.

you could try unbolting the slave and see if the bearing clips back in? but if it is damaged it will probably pop out again.

GTR260 Proficient

GTR260

Posted
  • Author
Posted

Got the box out over the weekend, problem was as expected, the circlip the retains the throw out bearing was in 2 pieces and bent as a mofo. Took it all to the clutch shop, they replaced the clip, machined the pressure plate and flywheel and repucked the clutch plate with new pucks. Right there and then, No questions asked all for $0. They even gave me a clutch aligning tool aswell.

Cannot ask for better service than that.

I just finished bolting the box up to the engine, hsve to wait on a few things from Nissan before I can get it driving again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
    • Duncan
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By Duncan · Posted

      Yeah that looks like great caster, but I'd suggest trying less front camber some time and seeing if it helps with braking without reducing mid corner speed too much
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      I ended up setting the rear 5mm higher than normal to give some clearance.  My plan is to run the least camber I can in the rear which I think with the extra width is going to need to be -1.75 to -2.00° just to get clearance.  Guards have been rolled and pulled as much as they can/I would be wanting to.  front has the Acostal knuckle with the KPI change and the drop etc. So should be okay with the existing settings I have run with AR1s etc Front: Toe total -2mm(1mm out each side) Caster +7.5° Camber -3.8° Ackerman +15°
×
×
  • Create New...