Jump to content
SAU Community

Recommended Posts

Hi all,

Got my engine rebuilt forged internals etc standard head just with 256 cams

Cranked the engine to build oil pressure, cranked it for like 5secs got 80psi pressure, started the car up and straight away lifters started tapping off its head,

Before anyone says take it to engine builder, I will on Monday when he open but been weekend Ill like to try work out what's wrong with it,

Nitto oil pump, still running VCt, blocked middle, 1.5m rear restritors,

Only thing I'm thinking is engine builder didnt do cleanances right? But I highly doubt it,

Bad lifters? How can I tell?

Link to comment
https://www.sau.com.au/forums/topic/419630-urgent-help-needed/
Share on other sites

Hydraulic lifters sorry,

Thought that as well, we had it at normal temps, (half way) took it just for short drive under 3000rpms and still ticking,

It seems to rev slow like it revs and the come down revs is slightly sorry

I was so nervous to start it as I have had so many issues in regards to work that was done on it, I didn't wanna start it... But just from

How loud they are and all the time doing it, I didn't wanna risk driving it and causing more damage, but yes they have been out of the motor for about 7months dry,

If its a fresh build you shouldn't be idling it or taking it on a light/brief drive.

You should be seating the rings or you'll stuff the build entirely. Tow it to the builder/dyno Monday and don't keep starting it now. All you should do on a fresh build is let it run for a couple mins just so you find any potential water/oil/air leaks etc.

yeah fair things i wanna check like cam cover just to make sure its not hitting it was late yesterday arvo 5pm and once i heard the noise i didnt want anything to do with it for the day was a let down she packed up closed the shop lol

Was the previous engine blow up a spun bearing by any chance??

It's so common this happens when a small bearing particle blocks the head oil feed from the previous blow up and you end up with stuff all oil to the head.

It's bloody hard to have the galleries cleaned out perfectly unless the original restrictors are removed.

A lot of engines I've seen built by various Motorsport teams like the supercars have external feeds to the cylinder head with inline filters to prevent this happening.

Hole bottom end was destroyed in the old motor, started again with block and crank, only think that didnt change was the head, but engine builder knew what happen with old motor and I told him to wash the head and he said he would do that,

Only thing that was used from the spun bearing motor was the head, lifters and cams? Could these of been f**ked from the old motor? I asked the engine builder to check everything to make sure it was all good to go back in

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...