Jump to content
SAU Community

Nistuned Z32 Ecu Suited To S1 R33

Pattey21
 Share

Recommended Posts

Pattey21 Proficient

Pattey21

Posted
Posted

Hey guys just bought this nistuned Z32 ECU.

ECU no# 23710 46P00 which is the correct 8 bit ecu to use

Also has the type 2 Nistune Daughterboard to suit S1/S2 R33.

Reason for selling is, i was told it was to suit s2 However after pulling it apart to inspect quality of ECU modifications required to suit r33, i discovered that it has been modded to suit series 1 and not 2. I am an electronics tech and all the modifications are done professionally.

I can revert this to suit r33 s2 but as it has cut tracks to suit s1 and removed resistors it would be a pain to do.

Price is $465 posted this is exactly what i paid last Friday.

Price is superfirm as in the case where it doesnt sell, i will put in the effort to suit the s2.

Feel free to ask any questions

Cheers

Patrick

post-88652-0-49930100-1360748139_thumb.jpg

post-88652-0-65440700-1360748163_thumb.jpg

post-88652-0-44017700-1360748192_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/419901-nistuned-z32-ecu-suited-to-s1-r33/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • joshuaho96
      GTX2867R GEN 2 NO OUTPUT FOR BOOST SOLENOID

      By joshuaho96 · Posted

      From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • MBS206
      Nissan Skyline R34(ER34) Front Suspension Noise

      By MBS206 · Posted

      I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Summernats cruiser?
    • MBS206
      NC MX5

      By MBS206 · Posted

      Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...