Jump to content
SAU Community

Recommended Posts

i would say because the 89 models are pretty rare, and would be very expensive in japan just like any of the old Skylines ie 72model GTR GC210 or 110 whatever they are, if they werent rare we would be seeing them popup on the japanese importer sites like j-spec or prestige motorsport, but until this day i have never seen on on either of those sites...

Link to comment
https://www.sau.com.au/forums/topic/42024-89-honda-nsx/#findComment-860402
Share on other sites

The NSX wasnt released until 1990 so that is the reason. I had a chance to purchase a 1990 model for $40,000 but I would have been unable to register it until next year. I love the NSX.

are you sure they didnt come out in 89 because im sure ive seen on a Japanese website an owner of a 89 model Honda NSX but this could also be wrong?

Link to comment
https://www.sau.com.au/forums/topic/42024-89-honda-nsx/#findComment-860406
Share on other sites

Justin is spot on, they are 1990 and the cheapest ones are Autos and they are by no means cheap at all...so you can imagine how expensive a manual one is. Even the Japanese feel these cars are expensive, not to mention there really isn't that many here...I'd even say there weren't many sold globally in other countries as well.

Looking at the import side of things, if they're such a bargain you wouldn't be the first to know. 40K+GST+import tax, makes the local ones a bargain...is what I tell everyone.

along with wat everyone else says, all the older ones have been in accidents and with an all aluminium frame, it wouldnt be a good idea to buy one.

Spot on again...aluminium panels cannot be repaired, they have to be bought new and do you know how expensive Honda sells them?

Nice try though...I don't know how many people I've already told who thought they were onto a gold mine.

Link to comment
https://www.sau.com.au/forums/topic/42024-89-honda-nsx/#findComment-860793
Share on other sites

Yep, NSX sold from 1990... September 1990 in fact.

 

NSXs are so sought after in Japan, even the cheapest, most poorly kept auto trans shitter 3.0L '90 model still commands 2.5 million yen...

Don't get me wrong, i'd love a NSX, but why are they so sought after? They overall better than a GTR or RX-7 are they???

They always been 3ltr V6??'s ?

Link to comment
https://www.sau.com.au/forums/topic/42024-89-honda-nsx/#findComment-860819
Share on other sites

the originals wer 3L v6 but then they wer changed to 3.2L v6

The reason they are so sought after is because they are Japans only true Supercar. Mid engine layout, Normaliy Aspirated, Lightwight, Brilliant Handling, a True Sports car. That is why i believe they are a sought after item.

Link to comment
https://www.sau.com.au/forums/topic/42024-89-honda-nsx/#findComment-860844
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...