Jump to content
SAU Community

J O I N T H E D A M N D O T S

GTR-N1

By GTR-N1,
in New South Wales

 Share

Recommended Posts

xntrq Veteran

xntrq

Posted
Posted

I have no problem with speed cameras. If u dont speed u dont get fined or lose points. Speed cameras, mobile or fixed aren't a problem. Drink drivers and actual hoons are a problem as are fatigued drivers. Middle aged men who can't time manage properly and leave for work 20 mins late and HAVE to tailgate in their sporty as f**k Mazda 6 are a problem also. Just sayin'

I have to admit my occasional guilt to this here, though in my 34.

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Lol I'm late far to regularly, but that doesn't mean traffic can do 50 in a 70 zone. I agree with the speed cameras and red light cameras, if only they displayed the speed properly at Moore Park road :angry: . Safety cameras only work where people know how to drive and have common sense, which on Sydney tend to be not that common (e.g. slamming on the brakes because light went yellow, even though you could have safely made it doing the speed limit, but then, who does the speed limit these days?).

Here's a standard: If it takes you more than thirty seconds to reach 60 km/h, get off the roads.

Not enough people blast their horns at below-par drivers. Car in front doing 60 in a 70 zone with nothing to prevent them doing the speed limit safely besides themselves? Depress horn button on steering wheel.

GoldZilla Grand Master

GoldZilla

Posted
Posted

Here's a standard: If it takes you more than thirty seconds to reach 60 km/h, get off the roads.

Not enough people blast their horns at below-par drivers. Car in front doing 60 in a 70 zone with nothing to prevent them doing the speed limit safely besides themselves? Depress horn button on steering wheel.

I do it occasionally on the freeway, but it seems that they think YOU are in the wrong, despite the highly-visible "Keep Left..." signs. Usually it's a quick flash of the high-beams as I approach them from behind - some people get it, and some people (it seems) don't know what their mirrors are for, or why the hell I'm flashing.

It's even more annoying when there are a CHAIN of cars all swapping into another lane to overtake a right lane hog, and it still doesn't sink into that person's head.

:domokun:

GTR-N1 Grand Master

GTR-N1

Posted
  • Author
Posted

Observed Cultural Differences Years Ago

(I don't know if anything has changed)

* Hong Kong - Flash the lights > people move

* Bangkok - Toot the horn > people move

* Sydney - Flash the lights > people stay put

* Sydney - Toot the horn > you cop middle finger

* Sydney - Blast the horn > people brake hard

* Sydney - Train Horn > people move

xntrq Veteran

xntrq

Posted
Posted

Observed Cultural Differences Years Ago

(I don't know if anything has changed)

* Hong Kong - Flash the lights > people move

* Bangkok - Toot the horn > people move

* Sydney - Flash the lights > people stay put

* Sydney - Toot the horn > you cop middle finger

* Sydney - Blast the horn > people brake hard

* Sydney - Train Horn > people move

Got tooted yesterday going over a rail crossing at about 50km in a 60 zone. Not to mention the rail crossings are terrible and it's like a roller coaster ride. I resisted my urge to do the both.

I think the major factor is mentality and daily stresses that people go through. Putting up with terrible traffic 24/7. I've found the further away from Sydney you go, the friendlier the traffic is.

PN-Mad Grand Master

PN-Mad

Posted
Posted

Sydney has nothing on Victoria.

We have to make sure it doesn't end up like our Mexican neighbours.

Driving down the freeway- these are my notes/differernces

-Fixed speed cameras have nil signage warning of their location

-Police actively hide, including behind bridges, and within bushes in the median strip making it impossible to see them.

- Unmarked random cars parked on the side of the highway contain speed cameras.

- Cameras on the back of bridges

And lets not forget the polices shoot and ask questions later policy.

ras1983 Experienced

ras1983

Posted
Posted (edited)

Train horns are for chumps. Real mean use ship fog horns:

On a more serious note, NSW isn't anywhere near as bad as Vic. Just stick to the speed limits and we won't have to pay voluntary taxes. Cruise control comes in very handy for this purpose.

Edited by ras1983

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...