Jump to content
SAU Community

Recommended Posts

A couple months ago I noticed my r33 gtst hicas ball joints were flogged but neglected the issue. I recently had a full wheel alignment done and the rear end is still snaking under acceleration and deceleration, so i decided I'd better have a closer look at the problem. As expected the balljoint are creating play and they need to be replaced asap. I've had a solid look on the net for the best upgrade without buying a whole hicas lockout system and not much luck. I have a lock bar already and i dont want to tamper with the aligment since i just paid for one. Does anyone know where i can get solid bushes to replace the worn ball joints or what the best upgrade would be. this is the only option i have found so far - http://www.jdmgarageuk.com/index.php?route=product/product&product_id=843. I've herd rubber(non solid bushes) would create unwanted play...

There are fairly inexpensive ball joint replacements on ebay, made by a tawainese manufacturer. I dont have HICAS, but have used the other ball joints (2 sets front AWD ones, 1 set of rear ones) and theyve been fine.

http://www.ebay.com.au/itm/2-REAR-LOWER-BALL-JOINT-HICAS-NISSAN-SKYLINE-R32-R34-R33-89-02-/170765872227?pt=AU_Car_Parts_Accessories&hash=item27c2706c63

So i couldnt find ant upgrades that could be posted to australia and the ebay selling have really bad feedback(scammers and there ball joints dont fit plus they claim they aus sellers but are located in taiwan).

I ended up finding some genuine nissan r33 hicas ball joints on justjap for $80 a side. Hope this info can help others in the same situation.

Yeah cheers mate, makes sense. Justjap sent me 1 gtst ball joint and 1 gtr ball joint....any chance the gtr one would still fit? It has an extra fitting inside it on the back end that faces towards the front of the car but other then that it looks identical..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...