Jump to content
SAU Community

Recommended Posts

Hey guys,

Was just wondering if the front sway bar from an r33 gtr would fit a gts/t?

I know they do for the rear provided you have the gtr brackets (bare with me, just been reading about it this afternoon). And what other provisions are needed to get it to actually fit?

What matter anyway? Whiteline bars are not expensive.

I have 24mm adjustable (set soft) in the rear, 24mm adjustable (set hard) in the front, on an R32. Springs are much softer than a lot of people's (being Kings low). The handling balance is;

a) much better than it was in the previous setup where I had the same rear bar and the stock, hollow 22mm front bar. That was a very oversteery setup.

b) much much better than the setup prior to that, which had the stock (~18mm?) rear bar and the stock, hollow 22mm front bar. That was a committed understeer setup.

From the above I would strongly suggest that just throwing random available bars at cars is a bad idea. You need to start with a known good combo of front/rear sizing (unless you're prepared to try a few different combos to work it out for yourself). And even then you need to have some adjustability to account for difference in springs, dampers, alignment settings, tyres etc etc etc between different cars. Hell, even the driver's preference for which end lets go first requires you be able to adjust to suit that.

You raise a good point there, my luck ran out when the front gtr sways didnt fit ill have to source something else, as i thought the gtr combo would have provided a balanced yet stiffer ride, not all too keen on having them as an odd pair haha. New to the whole sway bar setup, i guess adjustables would be a good start?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
    • So....knowing that I have a problem with power steering temps on track and another Wakefield day booked in next Friday, I've done the obvious thing They are very reasonably priced at $1650, considering they are a big monotube shock, double height adjustable (don't have to change pre-load to change ride height), one way adjustable damping and standard sized and customisable springs if you want something other than what comes with them. They come with 9kg/mm front and 4.5kg/mm front and I went with that as a starting point because I'll add adjustable sway bars too https://justjap.com/products/bc-racing-coilover-kit-ds-ds-infiniti-q50-v37-14-current#description Unfortunately they didn't come with rear strut tops so I've re-used the factory ones which was a bit of a pain. Also, the adjuster for the rear shock will be an absolute nightmare to get at, and while there are extensions in the kit I can't see any way you can actually attach or use them
×
×
  • Create New...