Jump to content
SAU Community

Recommended Posts

Hi Guys,

Truly appreciate all your help as it helps me out quite a bit.

I'm ready to install my oil catch can setup but I'm a little confused as to where i am going to put the little "filter" to make my crankcase still ventable.

I've got a Greddy can which has (2) inlets, my PCV valve is capped off, and my (2) breathers up top T together and would only use up (1) Greddy oil can inlet; which leaves the other inlet on the catch can open. Should i place the little filter on this open inlet?

062683F8-63CA-4BAB-B655-CAAC0DE03099-202

D2D46D66-E005-40A7-9595-7DD20CD156B5-202

Link to comment
https://www.sau.com.au/forums/topic/421786-oil-catch-can-qs/
Share on other sites

^^^as above. I have plumbed mine into the intake. If you vent to atmosphere

1. its probably illegal

2 you can get undesirable smells wafting into the cabin

3 you may get oil mist making a mess of your engine bay.

IIRC, as a general rule of thumb

if PCV is blocked aren't you meant to leave it vent atmo....in which case just put a filter on the empty port

If you plumb it back to intake, then put your PCV back in...

I found that out the hard way, it's the whole reason for asking. I was vent to the intake pipe but had massive amounts of low by in the intercooler pipes.

Unblock the PCV and plumb it into the intake, the system works better like that.

You would be better off ditching that empty can to, even with steel wool they don't do a lot. I had one in my car for a good 2 years and there was never a drop in it, not even condensation. My new properly baffled catch can picks up a fair bit of condensation.

Unblock the PCV and plumb it into the intake, the system works better like that.

You would be better off ditching that empty can to, even with steel wool they don't do a lot. I had one in my car for a good 2 years and there was never a drop in it, not even condensation. My new properly baffled catch can picks up a fair bit of condensation.

I would rather not. I run a blow-through setup so connecting back the PCV and routing my breathers back to the inlet would mean i would then have a vacuum leak at idle as the PCV is pulling in air from the valve covers through the breathers which are now BEFORE the maf as it's in blow through.

Also, I opened up my inter cooler piping and had TONS of oil/blow by so I'm almost positive a catch can will be better for my setup.

I would rather not. I run a blow-through setup so connecting back the PCV and routing my breathers back to the inlet would mean i would then have a vacuum leak at idle as the PCV is pulling in air from the valve covers through the breathers which are now BEFORE the maf as it's in blow through.

Also, I opened up my inter cooler piping and had TONS of oil/blow by so I'm almost positive a catch can will be better for my setup.

Ah, fair enough then.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...