Jump to content
SAU Community

Rb25Det Parts Stripping Complete Rb25Det

toy515
 Share

Recommended Posts

toy515 Grand Master

toy515

Posted
Posted

Complete head with covers ready to bolt on $200

Complete head with adjustable gear no covers $180

Acl ross forged pistons good condition apart from a gorge from underneath of one piston $200

Rb25det block good condition $90

Rb25 sump $50

Rb25 s1 and s2 airflow meters $50 each

Injectors and rail $40

Coilpack cover $50

Crank angle sensor $60

Balancer $30

Intake plenum $30

Crossover pipe 20

Bov $20

Ac pump 40

Alternator 50

Power steer pump 50

Throttle bodie $30

Tbs $30

S2 tps 40

Flywheel $40

Engine brackets $40

Engine mount very good nick $40

Rb25 turbo and lines unknown condition $50

Turbo Manifold $30

Coilpacks all working $40

Coilpack harness very good condition still soft s1 and 2 $80

Injector loom $40

Under plenum loom $40

Knock sensors $30

And anything else I have missed

Gold Coast

0487924497

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Things are happening.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • Pac
      The New Official S A U - N S W Spotted Thread

      By Pac · Posted

      I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • Komdotkom
      NC MX5

      By Komdotkom · Posted

      The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...