Jump to content
SAU Community

-Sa- R32 Rollcage, Bride, Hydro, Suspension, Coilovers

rb25r32gtst
 Share

Recommended Posts

rb25r32gtst Proficient

rb25r32gtst

Posted
Posted

Ok so stripping my r32 drift car

Smm modded front knuckles, great lock with no bind $400

Longer tie rods $50

Bolt on rack spacers $130

Brand new tie rod ends $50

All for $600

Unknown brand coilovers, spring height adjustable only, no leaks $600

Non hicas rear subframe, has been strengthened, has solid alloy risers $400

Nismo 1.5way diff with 4.3 ratio $750

Full 3" straight through exhaust with 4" tip, fits great, made by AM Performance $500

Genuine bride zeta 3, in red, with low bride rail $750

Driftworks hydro handbrake with flexible lines $300

Buddy parts full rollcage, with cross section between the rear stays, also double side intrusion. Best bolt in rollcages!

$1800

R32 gtst headlights $200 pair

R32 gtr indicators, next to headlight $200 pair

R32 gtr front guards, been rolled and lipped, Matt black, minor damage to lh $200 pair

Gtr copy bonnet, has flush bonnet pins in average condition, no dents $200

Stock passenger seat $50

Near new driftworks harness $200

Old school sabelt harness $50

Located in Adelaide but can post at buyers expense

Contact via txt on 0400384033 or pm

Can mms pics

reeceo21 Community Regular

reeceo21

Posted
Posted

Should keep some of that stuff if u buy my 32. Could make a very streetable drifter ;) if I didnt shell out 600 dollars of exhaust gear I would of snapped up those knuckles :(

Calsonic14U Mentor

Calsonic14U

Posted
Posted

Hey mate price on driftworks harness posted to 2148 sydney :) and whats the date on the belt expiry?? As on of mine has just gone out by 12 months lol.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...