Jump to content
SAU Community

Recommended Posts

Hi all

I have for sale my R32 GTS-T. I hadn't planned on selling it, but I'm now looking at buying a GTR.

It's a 1992 R32 GTS-T, I've owned it for over 5 years since the odo said 130,000kms & its now showing 210,000kms. Been a daily driver for most of its life, still puts out around 150kw at the wheels at 13psi on standard motor, turbo & ECU. Very reliable at this power level, never had any major issues other than general wear & tear maintenance. Oil & filter changed every 5000kms religiously.

I've been upgrading everything in the car ready for an RB26 conversion, & it's pretty much ready to go in right now. Mods are as follows:

R33 GTS-T front brake upgrade

BRAND NEW Exedy single plate clutch rated to around 700hp

rebuilt & shimmed factory LSD

upgraded UAS radiator

GTR front seats

GTR dials put into standard GTS-T dash

DVD player with separate 7" display screen

splitfire coils

walbro in tank fuel pump (500hp rating)

rb25 pink label AFM fitted & calibrated by Unique Auto Sports

turbosmart dual stage boost controller (11psi & 13psi)

17" black R34 GTT wheels (optional set of 17" antera wheels also but only has 2 good tyres on this set)

3" catback exhaust

aftermarket coilovers (just over a year old)

GTR bonnet with N1 lip & GTR grille (grille needs to be painted but i still have some paint left over)

dual pillar mount boost gauges (1 shows pressure in bar, other in psi)

Plenty of other mods I'm sure I've forgotten, car is due for its next 100,000km service so only gets driven short distances on weekends mostly. (I've been holding off to do the RB26 swap). I can look into getting this service done prior to purchase if requested.

Registered until June 2013, not had issues with rego or police for the past few years. (got defected once before & cleared before rego was cancelled, i was running a silly BOV & pod at the time, all plumbed back now).

Bad points:

clear coat is peeling in a few places, behind drivers door under quarter window & on the roof just behind the front windscreen

aircon needs a regas, was working fine until it ran out & i left it planning on the engine swap

central locking plays up, but the car can always be locked

alarm isnt making noise, but the immobilisers still work fine

passenger window isn't currently working, i believe due to the alarm auto-window lift malfunctioning. if you put power on the motor inside the door the window operates fine, & the switches are working fine also.

Located in western sydney close to minchinbury

Asking $7500, NO SWAPS PLEASE, i already have WAY too many toys.

OR

Price with included extras $13,000.

Extras

RB26DETT (N1 turbos, gates timing belt & modified RWD sump approx 9 litre capacity just fitted)

RB25 box & custom 1 piece driveshaft

PowerFC (& hand controller but unsure if it suits GTR, purchased separately & not tested)

Link to pics: http://s979.photobucket.com/user/cmoney9630/library/R32%20GTS-T?page=1

Any other pics you want that aren't already there, let me know as I may have some floating around.

PLEASE NOTE: extras are NOT for sale separately unless the car gets sold on its own first, thank you.

Best contact on here via PM, or 0407 896 339.

Cheers

Chris

Edited by cmoney
Link to comment
https://www.sau.com.au/forums/topic/423070-r32-gts-t-nsw-plenty-of-mods/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...