Jump to content
SAU Community

Recommended Posts

Hi all,

Am new to the Australian modified car scene. I've tried searching but cant seem to find a clear direct answer and some are in bits all over the internet. So here goes...(with regards to a BNR34)

Which of the modifications below needs an engineering cert? and if so, can we like do all together and then get an engineer to inspect and save $$?

- 19" rims with 255/35 tires

- ganador side mirrors

- carbon trunk

- carbon gt wing 1710mm

- aftermarket tie rods, lower arms, traction and camber rods etc

- strut bars

- sway bar and end links

- gauges mounted on the A pillar

- body kit

- front wide fender (nismo Z tune)

- turbo

- turbo outlet

- front pipe

- high flow cat

- cat back exhaust with jasma cert

- radiator

- intercooler

- coilpack

cheerio guys! :cheers:

Turbo for sure.. what no boost controller, injectors, ECU or Air Flow Meter? These all affect pollution control (EPA laws).

Depending on what state you're in cops will try to defect A pillar gauges "because they are in a crash zone". Yeah not likely if you have a front air bag! and how about taxi's and cop cars (and who's on the road more?). Anyway have the line added to the cert.

Not sure on side mirrors and aftermarket tie rods, lower arms, traction and camber rods etc

rest should be ok.

suspension stuff engineer can sign off on it and over ride the rules but the exhust not under hes power that you have to deal with epa.

thats a relief.... sort of.

are there legal aftermarket exhausts for the BNR34?

Theres nothing that comes with a ADR approved sticker on it if thats what you mean its bascially just up to you to make sure its 90db if you want it to be legal and pass, but doesnt really matter if it is or not because cops will report you on suspicion for exhuast sound as some people have been done on standard exhuast so theres not really a way to be 100 percent bullet proof on epa issues.

Also take into account the stock exhuast is basically the loudest you could have and be legal since it is around the 89db mark.

whats the approximate cost of an Engineering Certificate? If you became a member of a car club would that help alot in getting things approved , i mean if you say the car is used for limited use on road and the mods are for the track etc etc..

Theres nothing that comes with a ADR approved sticker on it if thats what you mean its bascially just up to you to make sure its 90db if you want it to be legal and pass, but doesnt really matter if it is or not because cops will report you on suspicion for exhuast sound as some people have been done on standard exhuast so theres not really a way to be 100 percent bullet proof on epa issues.

Also take into account the stock exhuast is basically the loudest you could have and be legal since it is around the 89db mark.

I think i read somewhere that we can go get it tested after installing the exhaust where they test for emission and sound rite? if that one pass...surely the cops wouldnt be THAT anal to book u if u have something to show that it was already tested?

also... are they crazy? stock exhaust and still book u?!?!? but i take it that u can contest it right?

  • 2 weeks later...

yeah so according to the ADR..even if they wanna fine u for something ....there has to be proof rite? so if EPA tests prove that its below 90db..then u're ok...rite?

the cops arent judge and executioner wat!

Edited by C4a0s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...