Jump to content
SAU Community

Aluminium Radiators

GeeDog
 Share

Recommended Posts

GeeDog Experienced

GeeDog

Posted
Posted

I have a few questions about fitting an aluminium radiator to my 03 coupe. My temp has drifted upwards several times over the summer, mostly when pushing hard on very hot days. Because I do some events in the car I want to try & stop this, and I'm thinking of replacing the radiator with a larger, more efficient one.

Does a 350Z alloy radiator fit into the V35, and are any mods needed. I'm looking at a 50 / 52mm thick core. There are a lot of 350Z radiators available.

Has anyone fitted an alloy radiator to a V35, and what effect did it have on temps?

My car is auto, and I've fitted a large auto trans cooler, in addition to the one in the radiator. Any thoughts on whether I need an auto radiator, or just a manual one with the external cooler?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/423687-aluminium-radiators/
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

You will most definitely need an auto radiator, but a 350z alloy unit will not fit. The neck is on the opposite side for a start. You could perhaps run a G35 radiator from the US like a few of the stagea guys run, but this won't fix your overheating issues. Do some research in the Stagea section, I and many others have had this issue for a while, and I have eventually had to design a mod to cool the block separately. I call it the VQ coolant mod, to help you search.

Nightcrawler Grand Master

Nightcrawler

Posted
Posted

350Z alloy radiators DO fit, but it takes some massaging to get it in. The biggest problem is that due to it being so significantly thicker than the stock V35 radiator the top and bottom mounts don't properly line up, so you have to modify them. Also it fouls slightly on the air conditioner hard lines, and the radiator pipes touched the fan shroud on the passenger side. In the end my Ebay alloy rad ended up developing a weeping leak in the core (presumably due to being wedged in my car for 2 years) and I have now put the oem one back in. All in all not recommended.

I did however also fit a Davies Craig trans cooler in front of the oem radiator, and disconnected/rerouted the trans fluid pipework. This takes a heap of heat OUT of the oem radiator, and makes it work better. I also fitted an oil cooler and again, this helps keep the whole lot cool.

My recommendation: keep the oem rad, disconnect the oem trans cooler pipes running through the radiator, fit a decent trans cooler, fit a decent oil cooler.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

^^ and be stuck with 4 gears most of the winter. It won't work well like that at all without a thermostatically controlled fluid supply or hiding the cooler away with a thermo fan. (not a good option) Keep the radiator fluid 'warmer', as the trans would never get near the engine temps without it anyway.

An oil cooler will not cool the water temps down too much, and the hassle with loading up the cold air space in front of the radiator is it then gets a gutload of hot air as it has already passed through multiple coolers before the radiator, making the problem worse. I agree an oil cooler is a good idea if you plan to track the car, otherwise it is a liability.

If you do a few searches, you will see a common trend, VQ's are a bitch to bleed and missing only a cup full of coolant can be enough to airlock the system, pushing water temps through the roof. Many an engine has been lost this way, mainly due to the poor design of the cooling system.

  • Like 1
GeeDog Experienced

GeeDog

Posted
  • Author
Posted

My trans fluid goes through the new cooler first, then the radiator, so it wouldn't be adding a lot of heat to the coolant. Its only got hot a couple of times, both on extreme heat days (one was 45 degrees, the other 42 or so) when under load. Daily driving isn't an issue - the gauge sits a fraction under half. I'm just concerned that a track day will be a major problem, and want a bit more cooling ability. I really don't think it's a bleed problem, I just think the cooling system isn't quite good enough for extreme conditions. I will put an oil cooler in before I do a track day, but I will probably also get a larger radiator. I've found some 40mm V35 ones, so I might try one.

Thanks for the input - it was helpful. NC - where did you mount the oil cooler? I'm running out of space as I've already fitted a large trans cooler on the LHS, and a larger than stock Power Steering cooler on the RHS.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • Kinkstaah
      Wheel Sizes & Offsets For Skylines

      By Kinkstaah · Posted

      If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...