Jump to content
SAU Community

Not My Day Today

ecl

By ecl,
in R35 GTR

 Share

Recommended Posts

ecl Mentor

ecl

Posted
Posted

So drove down the southern highlands from sydney today. On the way home near heathcote, car suddenly feels like its losing power and I get a TCM error.

Pull over and restarted the car cool down and tried restarting but still had the error. Had my Cobb on me but for some strange reason, after plugging in, it just loads the AccessPort screen.

Anyways, realised the car only had 1,3 and 5 gear and was in limp mode (I think) as it feels the car limited my speed to under 40 km/h.

Will be taking it to the workshop on Monday (out of warranty and cobbed so doubt Nissan will like that) but from reading, I suspect it could be a solenoid or sensor. Though it obviously could be something more serious =(

If you have had the issue before, could you shoot me a PM please =)

Thanks

Link to comment
https://www.sau.com.au/forums/topic/424184-not-my-day-today/
Share on other sites
domino_z Mentor

domino_z

Posted
Posted

if it was something major the car wouldn't be driveable

most likely pressure sensor or solenoid

either way nissan dealer wont attempt to trouble shoot beyond ecu codes, their suggested and only fix will be a replacement trans - dealers aren't mechanics

best put the car on a truck and send it to willall

Speedah Enthusiast

Speedah

Posted
Posted

So drove down the southern highlands from sydney today. On the way home near heathcote, car suddenly feels like its losing power and I get a TCM error.

Pull over and restarted the car cool down and tried restarting but still had the error. Had my Cobb on me but for some strange reason, after plugging in, it just loads the AccessPort screen.

Anyways, realised the car only had 1,3 and 5 gear and was in limp mode (I think) as it feels the car limited my speed to under 40 km/h.

Will be taking it to the workshop on Monday (out of warranty and cobbed so doubt Nissan will like that) but from reading, I suspect it could be a solenoid or sensor. Though it obviously could be something more serious =(

If you have had the issue before, could you shoot me a PM please =)

Thanks

Most probably pressure sensor fail...same problem I had.

Dont bother will Nissan...if your car is modded they will diagnose then charge you to say they cant help.

If you want to transport your car to Willal in Adelaide by someone who cares about your car let me know

Kev

  • Like 1
ecl Mentor

ecl

Posted
  • Author
Posted

They managed to pull the codes using their AP but I didnt ask them what they were as I was flat out today. I'll ask them tomorrow but they mentioned they got the usual plus one they haven't gotten before.

They also cleared the codes and it drove fine again for a bit. Then they went from 5th to 6th and the the transmission oil pressure shot up to double and the the t/m malfunction and limp mode came back on. I'm assuming this is pressure sensor or related.

In any case, the gearbox is coming out tomorrow to get fixed.

  • Like 1
Brockas Proficient

Brockas

Posted
Posted

P2832 - Shift Fork 'A' Position Circuit Range/Performance

Solution for the aftermarket appears to be the TSB Clip (assuming your car is 2011+).

Taken from 'Jacks Transmissions': ( http://www.jackstransmissions.com/pages/gtr-gr6-clip-tsb )

The shift pistons in the valve body make contact with the forks and move them into position. If these pistons wear, the forks and sliders will no longer shift properly and can be damaged. This is a common problem with the GR6. Prevention is to perform this TSB.

We have never encountered these problems again after performing this TSB so it has become standard procedure to install clips in every unit we touch.

APPLIED VEHICLE:2009 – 2011 GT-R (R35)

For 2009 - The MIL is on and DTC P0729 (6GR Incorrect Ratio) is stored,
For 2010 - The MIL is on and DTC P0729 (Sleeve A1 Function) is stored,
For 2011 - The MIL is on and DTC P2832 (Shift Fork A) is stored,


Here is a picture below of the wear. Note the circled area. It doesn't look like much, but that is enough to cause thousands of dollars in damage:

DSC06452_grande.JPG?648

The clips will allow for better contact with the piston and prevent the wear or failure.

There are a series of magnets inside the piston which will become out of range of the sensor if the assembly wears too far. This will prevent the system from recognizing where the piston is moving and the unit will shift the fork too far as it doesn't know the forks location. This is what will break the fork along with the slider. This simple TSB solves any issue you could ever encounter with the fork or sliders. Well worth performing while you have your pan out and this TSB can be completed while the trans is in the vehicle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • tidi0x
      Nismo GT Pro LSD configurations

      By tidi0x · Posted

      I have wasted too much time on this, more than I am willing to admit. I hope someone can set the record straight for me.  I want to replace my Nismo (non GT pro, non GT) standard 2 way in my R33 GTST with a 1.5 way... Ideally I want to get an ATS 1.5 way Carbon LSD, but I don't want to reuse my 29 spline 5x1 axle stubs, and new 30 spline 5x1's are impossible to get a hold of ($$$), and I don't want to drop the cash on going to 6x1 stubs and axles ATM. Which leads me to the Nismo GT Pro 38420-RSS15-B5 or RSS20, as they come with new axle stubs meant for the diff, and is "Convertible" from a 2 way or 1.5 way to "Other ways", but that is where I am stuck as the documentation is a bit all over the place.  To sum up what I have found I believe the all the Nismo GT Pro PN's are convertible from 2 way, 1.5 way, and 1 way; but Nismo sells 2 skus (2 & 1.5) so people do not have to disassemble to convert it.  I found this thread on 350z but it left the question unanswered. https://my350z.com/forum/engine-and-drivetrain/620032-nismo-gt-pro-lsd-1-5-vs-2-way-and-torque.html  Essentially the way I think it all works out is like follows...  2 way  1 way  and 1.5 way would be the center pinion shaft in the 1 way block, but with the with the center flipped 180*. So the ramped side of the pinion would face the 1 way gate and act like a ramp.    I can only get my hands on the 2 way in the states, and I am not trying to get stuffed on tariffs by ordering from Japan or anywhere else. I want to confirm that if I get the 2 way I can convert it to the 1.5.     
    • StevenJames32
      Single Turbo Conversion Lines.

      By StevenJames32 · Posted

      Hi everyone, I have purchased my first GTR and I want to do a single turbo conversion to it. I've been doing as much research as i can and there are a few things that I can find and need to know. I need to run a coolant feed, coolant return, oil feed and oil return for my turbo setup. Here's what I know so far: On the hot side of the rb26 there is coolant feed, oil feed and oil return. Coolant return will be going around the front of the engine to where the thermostat is located. I will need to block off the rear oil return port. I will be running a turbosmart boost solenoid so any of the factory boost stuff wont be needed. Now onto what I don't know: 1. What do I do with the coolant / vacuum hardlines that run around the back of the motor?. 2. What do I block off or loop or move or remove?. I will be running the OEM intake manifold. 3. Is there anything in particular I need to buy for the cold side of the rb26?. I already have the intercooler and pipes sorted. If you have any pictures or information it would be appreciated. Thanks....  
    • Murray_Calavera
      "Cheap" bolt on turbo on RB25DET NEO

      By Murray_Calavera · Posted

      The fab work can be as simple as a couple of silicon hoses and clamps to the factory piping. 
    • joshuaho96
      "Cheap" bolt on turbo on RB25DET NEO

      By joshuaho96 · Posted

      Just sounds like either way you need to do some fab work to get everything to fit, so why limit yourself at that point? If the GCG high flow option is zero effort in and out swap though I'd probably do that. It's almost certainly lowest risk, lowest cost, etc. The HKS GTIII-RS option that Kapr mentioned is laughably expensive for what it is, they charge the exact same for two turbos on the RB26 so their margins are off the charts on that thing.
    • GTSBoy
      "Cheap" bolt on turbo on RB25DET NEO

      By GTSBoy · Posted

      Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
×
×
  • Create New...