Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Now in the correct topic lets try this again.. Everyone needs to go and like Tectaloy Performance Coolants on facebook and like this post!! Apparently each like counts as a vote :D

post-109116-0-29397000-1369383088_thumb.jpg

Tis in the very first post in this thread

 

but good job on bumping this up :thumbsup:

Yeah this is different. If you actually 'like' Tectaloy's status it will count as a vote I think.

Thanks for your vote so far. As mentioned the voting system has changed. It now includes Facebook likes. If you have a Facebook account, can you please like our photo?

https://www.facebook.com/photo.php?fbid=553164344735803&set=a.543180885734149.1073741826.309582495760657&type=1&relevant_count=1


Your votes so far has kept us in the top contenders and is very much appreciated.

Hi Everyone,

Thank you again for all your support. We have made it into the competition.

Now we need to build our cars and get some more practise :)

The TOP 4 voted drift teams who will now compete in the 2013 Tectaloy Team Drift Challenge have been announced!!

1. Team Drift Mob - Total Points 436
2. Team Red Stage - Total Points 425
3. Team Slide 'N' Destroy - Total Points 413
4. 3 Fingers Neat Blaze Unit - Total Points 389

In the event one of the TOP 4 teams are unable to compete, the teams with the next top votes will be selected.. these are...

RE Drift - Total Points 387
Hit and Run DC - Total Points 215
Stadium Drift Australia V8 Superdrifters - Total Points 184
Insane Drifters - Total Points 150
Feint Motion Drift Team - Total Points 145
Team Upset - Total Points 116
Marvel Drifters - Total Points 114

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...