Jump to content
SAU Community

Recommended Posts

I think it could be done 'fairly' easily. You'd need to run spacers to shift the inner part of the rim away from the rear shock and front camber arm. I'd guess at least 10-15mm. Then you'd definitely need to roll your guards quite aggressively...or purchase over fenders.

Will look pretty tough if you don't mind a bit of mucking around to get it together.

For your reference, from what I've heard the best rim combo to slip straight on with no mods is 9-9.5" width with around a +12 or thereabouts offset

I have run 19x9.5 + 12 with 25mm spacers on the rear, was running 245/35 rubber and could have gone up to 255's.

I'm now running R34 GTR rims and 265/35/18 and rubber and 25mm spacers, car drives about 10099993785492569% better. Bloody close to rubbing springs on the inside though.

It would be a VERY tight fit/may not fit, you will need spacers, camber, stretched rubber and rolled or probably flared guards to run the 10.5.

It will look fat as all f**k though.

  • 2 months later...

i have a set of these on my black 260. http://www.koya.com.au/?cars=endless-black-s2c-19 mine are 245 wide and not sure of offsets. we made front and back the same offset between the two offsets on the front and back of the standard mags. they clear the brembo's fine and can be customised to the desired offset at the factory. the biggest issue i found with mags was caliper clearance and in qld spacers are illegal and will get you defected

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
×
×
  • Create New...