Jump to content
SAU Community

Recommended Posts

I think it could be done 'fairly' easily. You'd need to run spacers to shift the inner part of the rim away from the rear shock and front camber arm. I'd guess at least 10-15mm. Then you'd definitely need to roll your guards quite aggressively...or purchase over fenders.

Will look pretty tough if you don't mind a bit of mucking around to get it together.

For your reference, from what I've heard the best rim combo to slip straight on with no mods is 9-9.5" width with around a +12 or thereabouts offset

I have run 19x9.5 + 12 with 25mm spacers on the rear, was running 245/35 rubber and could have gone up to 255's.

I'm now running R34 GTR rims and 265/35/18 and rubber and 25mm spacers, car drives about 10099993785492569% better. Bloody close to rubbing springs on the inside though.

It would be a VERY tight fit/may not fit, you will need spacers, camber, stretched rubber and rolled or probably flared guards to run the 10.5.

It will look fat as all f**k though.

  • 2 months later...

i have a set of these on my black 260. http://www.koya.com.au/?cars=endless-black-s2c-19 mine are 245 wide and not sure of offsets. we made front and back the same offset between the two offsets on the front and back of the standard mags. they clear the brembo's fine and can be customised to the desired offset at the factory. the biggest issue i found with mags was caliper clearance and in qld spacers are illegal and will get you defected

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...