Jump to content
SAU Community

Recommended Posts

Hi Guys,

I am having an issue with my nissan skyline r33 gtst.

I went to track days few times now and I get loss of power after first 5 laps. Power decreases significantly. At wakefield I can reach 175km/h on straight but after about 5 laps I can reach only 150.

So thats 10-20% power loss.

I assume this is because car is getting too hot.

Mods r34 intercooler, 3'' exhaust turbo back, boost controller 10psi. fuel pump.

-So far I have changed to use different oil from motul 8100xcess (10-40) to castrol edge 10-60.

-I flushed the radiator and put better coolant. I have not flushed the coolant in engine, the damn release screw is ridiculous to get to and unscrew.

-changed AFM, and fuel pump. so def not those and oh boy it drinks alot.

Any recommendations??

i bought the car of friend and he had the coils replaced few yrs back, i have his reciept.

well it has bigger intercooler, but i didnt want get front mount and restrict the radiator.

i suppose i should turn boost down and see if i still get the problem.

i bought the car of friend and he had the coils replaced few yrs back, i have his reciept.

well it has bigger intercooler, but i didnt want get front mount and restrict the radiator.

i suppose i should turn boost down and see if i still get the problem.

dont worry about restricting the radiator.... you have no where near enough power to do that.

my theory is after a few laps of full throttle you ic is getting warm. maybe try a front mount.

depending on the coils he put in they could also be breaking down due to heat.... remove cover if you can to increase air flow.

also if you have apod filter put standard air box back in. same thing happens as with small ic, filter starts sucking in hot air from engine bay and you lose power.

hey, thanks for advice.

i will lower boost to stock boost 6psi for next trackday, to see if it helps. That should show if intercooler is problem.

I removed cover for coils already.

the pod filter is just behind the light so that should get enough cold air in.

Do you think the old coolant in the engine could be the issue?

hey, thanks for advice.

i will lower boost to stock boost 6psi for next trackday, to see if it helps. That should show if intercooler is problem.

I removed cover for coils already.

the pod filter is just behind the light so that should get enough cold air in.

Do you think the old coolant in the engine could be the issue?

nah mate wont be coolant. unless engine is overheating...

that pod filter will not work.... unless you remove the light....

It would most definitely be the little side mount cooler as Paul causing your loss of power.

I remember my XR6 Turbo had the same issue with heat soak and the standard cooler.

As soon as I put a big front mount on it, problem solved.

Lowering the boost will help but then you'll just have that same constant low power.

this.

honestly. buy a standard airbox. alot of guys with nearly 300kw still run them. search if you dont believe me...

Or like mentioned before, remove headlight (easy enough to do in a couple of minutes at a track, a couple of plugs and some nuts), and put a headlight replacement air intake in place (just jap have them) and box off your pod filter. Induction cant get much colder than that.

+1 for heat soak. The 34 cooler might be an ok upgrade for on the street, but they are rubbish for the track. Put it on a dyno and after a few runs power will start to drop substantially. That is where a fmic is an upgrade. It doesn't give you any more power, but it increases how long you have power.

  • 1 month later...

hey guys,

i found what the problem was, too high boost, through my intercooler

i went to trackday on friday @wakefield park , and i lowered the boost from 11psi to 6psi, and this solved the problem. I did 10 laps straight and had no issues with loss of power.

most of time now i do 5 laps, then 1 slow lap, then repeat.

i think r33 has dual stage boost, as it goes up 6psi, but after 4-5krpm it goes up to 10psi, but i didnt have any issues.

anyways thanks for help, and do try wakefield park on weekdays, it was open track all day not many cars at all. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...