Jump to content
SAU Community

Recommended Posts

Correct. They slip together and have two bolts holding them.

Its a recognised method of attaching legs and perfectly fine to do but a fully welded joint is best.

The way AGI do theirs is a better design with the 44mm tube and 38mm tube slid inside it. The fence post clamp together joins are rubbish.

So what's your equivalent product then?

I was considering that cage with the two diagonals (assuming it adds head protection for both occupants in a roll). Then welding in some base plates to bolt too. That's 880 delivered and painted.

What would your cage, painted and freighted cost and what work would I have to do when it gets here.

I wouldn't put both diagonals in the hoop.

One in the hoop and one in the rear legs with a harness bar in the main hoop as well.

Main hoop

Two rear legs

Harness bar

Hoop diagonal

Rear leg diagonal

12.9 high tensile bolts

Plates to be welded to body.

TIG welded (ER70s-2 filler rod)

German CDS material.

Ill do that cage for $770 plus the deliver cost which would probably be $140-$150.

When you get it you'll need to remove the seats and centre console

Remove the seat belts and rear trim etc.

Weld in the base plates for the main hoop

Drill holes for the rear leg plates

Bolt the cage to the base plates and then reinstall the seats, harness and trim etc.

OK cool, thanks for your help so far.

So to confirm, that cage comes as one piece fully welded and the only bolts are the ones used to fix it to the welded plates the car (are the plates meant to be welded for the backstays as well?).

Also, do you do/know what the best option is for lowering the seat.

My helmet sits too close to the roof at the moment.

I can see ways to get it lower but wondered if you offered something off the shelf.

Also, I assume it's most beneficial to TIG weld the plates in or is MIG sufficient for that weld?


Edited by ActionDan

Further to my questions above, another member has contacted me explaining that he'd like a cage too so with that in mind, is there the possibility of a discount on the cage or freight if we order 2? Would they both fit on one pallet etc?

He's currently waiting for pics from Roy, but if you have any now is a good time to throw some up.

No off the shelf solutions for seats I'm afraid.

Mig welding plates to the floor is the only way. TIG welding to a floor pan is very difficult and ugly.

I'm sure two cages could go on one pallet yes.

I don't actually have photos of troys cage. I do that many I don't normally take photos anymore.

I think there may be some in his build thread though.

Does this look like it?

gallery_20349_4009_25906.jpg

I demand $50 from anyone that posts pics of my car :)

Brad must have taken that pic as it doesnt look like one of mine.

It is SCHMICK! I am not saying that because its my car. I am not saying that because Risking is on the forum. I had the BD cage and was happy with it generally for the 2 or so years I had it. It isnt a question of better or worse etc. I got what I asked for from BD. If I had of articulated my requirements better I would have paid more and probably got what I was after but was mostly scared of rendering the back seat completely useless for storage of tyres and bags on a trip to the track

When I knew what I really wanted Brad was able to give it to me. I can still fit two 17" rims in the back seat. two in the passenger seat and fuel in the boot. When a recliner seat is in it goes a fair way back for some zzzzz when I am doing the Melb-Syd drive at night. Its all I could ask for since my thing is only a club car and needs to be driven on a daily basis

What do people think of something like this harness wise?



http://www.revolutionracegear.com.au/index.php?PCID=10413&PSO=245&PSID=9193133&PSV=Primary&CDO=



I thought at least 5pt for the anti submarine belt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...