Jump to content
SAU Community

Recommended Posts

It's caused by having too much negative camber for the type of driving you do. If you drive in a straight line most of the time (ie, not on a track) then you cannot have much neg camber or you will wear the insides of the tyres. At the rear, the problem is made worse if you like to spin them up.

And yes, this is caused by being too low. As you lower Skyline rear suspension you automatically gain neg camber. You need adjustable polyurethane upper inner bushes at a minumum, or adjustable upper arms.

This has been discussed at great length, including recently, including the legalities of the various options. So have a look around.

Link to comment
https://www.sau.com.au/forums/topic/425081-tire-wear/#findComment-6847416
Share on other sites

Have this same problem, but didn't realise until recently.

I dont track or spin the rears, just normal daily street driving. My car is lowered and has -2 camber from what was on my receipt when i got my wheels aligned after the drop.

Link to comment
https://www.sau.com.au/forums/topic/425081-tire-wear/#findComment-6847803
Share on other sites

yes there are shops and i cant suggest any cos im in sydney but i just want to reiterate that if you want to stay lowered then you will have to use adjustable bushes to eliminate camber OTHERWISE if you purely want to adjust coilovers to eliminate camber you may be going back to stock height.

Link to comment
https://www.sau.com.au/forums/topic/425081-tire-wear/#findComment-6848616
Share on other sites

yes there are shops and i cant suggest any cos im in sydney but i just want to reiterate that if you want to stay lowered then you will have to use adjustable bushes to eliminate camber OTHERWISE if you purely want to adjust coilovers to eliminate camber you may be going back to stock height.

How much am i looking at for adjustable bushes, and do most mechanics/tyre places have them readily available?

Link to comment
https://www.sau.com.au/forums/topic/425081-tire-wear/#findComment-6849069
Share on other sites

Pretty much no mechanic or tyre place will have adfjustable bushes to suit any car (except maybe Commodores!) in stock. Pretty much any tyre place cannot be trusterd to spin spanners so discount them immediately. Pretty much any mechanic could order bushes in within a day. If you fit bushes you need a set for the upper inners and a set for the inside/front ends of the radius arms as well. This will cost you a couple of hundred.

The arms need to come off and a press used to get the old bushes out and new ones in most of the time. The labour will probably end up costing more than the bushes.

Adjustable arms that have rose joints on the end (like the GKTech ones) are not street legal. Adjustable arms with bushes (such as Hardrace ones) probably are.....but you might be in for an argument with a cop and then the pain of getting it defected and having to clear the defect anyway.

Link to comment
https://www.sau.com.au/forums/topic/425081-tire-wear/#findComment-6849111
Share on other sites

Rose joints. Heim joints. Ball joints. They're metal on metal. Really good location and articulation, but......extra NVH, they wear out because they get grit in them, they are an instant defect should a cop see them, and sometimes the cheap ones are shit quality and break.

Hard Race is a brand that does adjustable arms and the like but with hard rubber bushes in them instead of the rose joints used in most adjustable arms. There are one or two other brands out there that do the same. Bushes are squidgy material between two shells to allow arms etc to have some compliance instead of hard metal-metal contact.

Link to comment
https://www.sau.com.au/forums/topic/425081-tire-wear/#findComment-6849766
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...